Jenn-Air W10394706A Installation Requirements, Tools and Parts, Location Requirements

Page 3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

Adjustable wrench

For LP/Natural Gas

Tape measure

Conversions

Adjustable wrench

 

Marker or pencil

³⁄₈" drive ratchet

 

Pipe wrench

½" deep-well socket

Flat-blade screwdriver

7 mm nut driver

 

¹⁵⁄₁₆" combination wrench

Masking tape

 

 

Wrench or channel lock pliers

Pipe-joint compound resistant to LP gas

Noncorrosive leak- detection solution

Parts Supplied

Check that all parts are included.

Gas pressure regulator

Burner grates

Burner bases and burner caps

Griddle drip tray (on griddle models)

Foam tape

LP orifice package (W10393255)

Conversion label (W10393342)

NOTE: The cooktop is manufactured for use with Natural gas. To convert to LP gas, see the “Gas Conversions” section.

Optional Backguards

48" (121.9 cm) models must be installed with a backsplash if installing at zero clearance to a combustible backwall. See “Cabinet Dimensions” in the “Location Requirements” section for installation requirements.

36" (91.4 cm) Retractable Backguard Order Part Number 8284756

48" (121.9 cm) Retractable Backguard Order Part Number 8284755

9" (22.9 cm) Backguard for 36" (91.4 cm) Cooktops Order Part Number W10115776

9" (22.9 cm) Backguard for 48" (121.9 cm) Cooktops Order Part Number W10115777

33½" (85.0 cm) Retractable Backguard with Wire Shelf for 36" (91.4 cm) Cooktops

Order Part Number W10285448

33½" (85.0 cm) Retractable Backguard with Wire Shelf for 48" (121.9 cm) Cooktops

Order Part Number W10285449

To order, see the “Assistance or Service” section of the Use and Care Guide.

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

High Altitude Conversion

To convert the cooktop for elevations above 6,560 ft (1999.5 m), order a High Altitude Conversion Kit.

Part Number W10394296 - LP high altitude

Part Number W10394295 - Natural gas high altitude

To order, see the “Assistance or Service” section of the Use and Care Guide.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base.

It is recommended that a 600 CFM or larger vent hood be installed above the cooktop.

It is not recommended that a microwave hood combination be mounted above the cooktop.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Grounded electrical supply is required. See “Electrical Requirements” section.

Proper gas supply connection must be available. See “Gas Supply Requirements” section.

The cooktop is designed to hang from the countertop by its side or rear flanges.

The gas and electric supply should be located as shown in “Gas and Electric Connection Locations” section so that they are accessible without requiring removal of the cooktop.

Provide cutout in left rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

3

Image 3
Contents Installation Instructions Your safety and the safety of others are very important Cooktop SafetyInstallation Requirements Tools and PartsLocation Requirements Product Dimensions Side View of CooktopGas and Electric Connection Locations Cabinet Requirements 24 61.0 cm cabinet depth13 33.0 cm upper cabinet depth Gas Supply Line Electrical RequirementsGas Supply Requirements Type of GasBurner Input Rating Altitude Install CooktopGas Supply Pressure Testing Gas Pressure RegulatorTypical flexible connection Install Optional BackguardMake Gas Connection To Assemble Pressure RegulatorComplete Installation Install GriddleSingle Flame Burner To Adjust Flame HeightFlame Height Dual Flame BurnerGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator Burner orifice spud Complete InstallationGas Supply Pressure Testing To Convert Surface BurnersGasket LP position Gas pressure regulator Access capNatural Gas Conversion Burner cap Burner baseStrip Circuit Griddle 120V Control Wiring Diagram To Cooktop Stand-AloneBurner Cooktop Reignition Wiring Diagram Wiring DiagramsControl Input Votre sécurité et celle des autres est très importante Sécurité DE LA Table DE CuissonExigences D’INSTALLATION Exigences demplacementOutillage et pièces 27¹⁄₈ 68,9 cm Dimensions du produitEmplacements des raccordements au gaz et à lélectricité Vue latérale de la table de cuissonSpécifications du placard Gaz naturel Spécifications électriquesSpécifications de lalimentation en gaz Type de gazInstallation de la table de cuisson Instructions ’INSTALLATIONDétendeur Installation du dosseret facultatifRaccordement au gaz Assemblage du détendeurRobinet fermé Robinet ouvert Installation de la plaque à frireRaccordement typique par raccord flexible Compléter le raccordementAchever linstallation En affleurement avec le dessus de la table de cuisson Sur les modèles avec plaque à frireTest de pressurisation de la canalisation de gaz Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeurAchever linstallation Conversion des brûleurs de surfaceGicleur de brûleur Chapeau de brûleur Base du brûleur Conversion pour lalimentation au gaz naturelChapeau de Détendeur Louverture daccès Joint détanchéité Position LPSchéma DES Circuits Schémas DE Câblage SW2SW1

W10394706A specifications

The Jenn-Air W10394706A is a modern, high-performance appliance designed to enhance the cooking experience in contemporary kitchens. Renowned for its precision, innovation, and sleek aesthetics, this offering from Jenn-Air is a favorite among culinary enthusiasts and home chefs alike.

One of the standout features of the W10394706A is its advanced cooking technologies. It incorporates innovative induction cooking, which provides rapid heating times and precise temperature control. This technology allows users to not only cook more efficiently but also safely, as the cooktop remains cool to the touch, minimizing the risk of burns. The induction system also offers an impressive level of responsiveness, allowing for quick adjustments while cooking, which is crucial for achieving perfect results.

In terms of design, the Jenn-Air W10394706A boasts a sophisticated and modern aesthetic, fitting seamlessly into any upscale kitchen environment. Its sleek surface is easy to clean and maintain, with a minimalistic look that emphasizes functionality without compromising style. The unit is engineered with high-quality materials, ensuring durability, longevity, and an enduring visual appeal.

Another notable feature of the W10394706A is its advanced cooking modes and smart technologies. Equipped with smart connectivity, users can control and monitor their cooking from a smartphone or tablet, providing a level of convenience that is invaluable in today’s fast-paced lifestyle. Additionally, it offers a variety of pre-set cooking modes, enabling effortless culinary creativity and consistency in food preparation.

Safety is paramount with the W10394706A, which integrates features such as automatic shut-off and child lock functionalities. These features ensure peace of mind in any household, promoting safe cooking practices and preventing accidents.

Moreover, the W10394706A emphasizes energy efficiency, utilizing technologies that help reduce energy consumption without sacrificing performance. This focus not only benefits the environment but also results in savings on utility bills, making it an economically conscious choice for households.

Overall, the Jenn-Air W10394706A stands out as an exceptional kitchen appliance that combines cutting-edge technology, elegant design, and practical features. It caters to the needs of discerning cooks, offering versatility and efficiency while enhancing the joy of cooking and entertaining in the modern home.