Bloomfield 0443, 0412, 0471, 0482 Timer Adjustment Automatic Brewers only, Remove Tank LID Assembly

Page 16

SERVICING INSTRUCTIONS (continued)

IMPORTANT:

Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure. If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line.

NOTE: DELAY is the amount of time before a second brew can be initiated, and is factory set for 5 minutes. LOCK and ALARM are not used.

IMPORTANT:

Before setting assembly into tank, make sure tank lid gasket is properly seated on flange of lid. DO NOT OVER-TIGHTEN.

IMPORTANT:

When mounting thermostat, be sure to insert sensing bulb to the bottom of the bulb well. Tighten capillary lock nut only enough to ensure no water leakage. Excessive tightening is not necessary.

IMPORTANT:

When replacing heating element, also replace seal gaskets.

TIMER ADJUSTMENT (AUTOMATIC BREWERS ONLY)

The amount of water dispensed automatically during a brew cycle is controlled by the timer.

Place empty decanter (for Model 0482, use an airpot) under brew chamber. Press BREW button. Brewer should dispense one full decanter or airpot of water. To adjust amount:

Remove brew chamber and button plug. Adjust knob on timer; clockwise increases time. Run several cycles to check amount of water delivered. Replace button plug.

REMOVE TANK LID ASSEMBLY

Disconnect brewer from electric power. Turn OFF water supply. Remove top panel. Pull vent tube and inlet elbow out of basin pan.

On automatic models, pull water inlet tube out of basin pan. Remove basin pan.

On models with faucet, disconnect inlet pipe at faucet shut-off valve and outlet pipe at faucet.

Disconnect all wiring from thermostat, hi-limit, and heating element.

Loosen two nuts on tank hold-down bracket. Remove hold-down bracket by sliding short slotted end off of locking stud and lifting it off. Remove cover assembly by lifting it straight up.

Reassemble in reverse order.

REPLACE THERMOSTAT (COTHERM)

Disconnect brewer from electric power. Turn OFF water supply. Remove top panel.

Disconnect all wiring from thermostat only. Loosen and free jam nut from pass-thru fitting securing temperature sensing bulb. Remove two screws holding thermostat to bracket.

Lift out thermostat, sensing bulb and thermostat gasket.

Reassemble in reverse order. BE SURE the bulb well is fully seated in the tank fitting, and that the temperature sensing bulb is inserted to the very bottom of the bulb well.

REPLACE HEATING ELEMENT

Remove tank lid assembly per above.

Remove two hex nuts holding element to cover. Pull element from mounting holes.

Reassemble in reverse order.

685 77110 Owners Manual Horizon™ Brewers

14

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 685 Warranty Statement Specifications Table of ContentsApplicability Features and Operating Controls Automatic Brewers Features and Operating Controls POUR-OVER Brewers Precautions and General Information Agency Listing InformationElectrical Damage Burn HazardLeveling the Unit InstallationUnstable Equipment Hazard PLUMBER’S Installation Instructions Automatic Brewers Water Supply InstallationELECTRICIAN’S Installation Instructions Shock HazardOperation START-UPPreparation Brewing CoffeePrepare for Next Brew Cleaning Instructions Procedure Clean Coffee BrewerTroubleshooting Suggestions Symptom Possible Cause Suggested RemedyServicing Instructions Access PanelsShock Hazard Warmer Plates Temperature Adjustment Servicing InstructionsTimer Adjustment Automatic Brewers only Remove Tank LID AssemblyReplace Thermostat Cotherm Replace Heating ElementClean Solenoid Screen Replace SolenoidReplace HOT Water Faucet Coil Replace Timer AssemblyRepair HOT Water Faucet Procedure Delime the Water Tank Chemical Burn HazardExploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Service Kits Faucet Repair KitsWiring Diagram Wiring Diagram Telephone Fax

0472, 0482, 0471, 0443, 0412 specifications

Bloomfield, a prominent urban area within Australia, is recognized for its unique postcode identifiers: 0482, 0412, 0471, 0472, and 0443. Each of these postcodes represents dynamic regions that showcase a blend of historical significance and modern advancement, making Bloomfield a vibrant place to live and visit.

At the heart of Bloomfield lies a robust infrastructure that supports both residential and commercial activities. The area is characterized by its extensive green spaces, parks, and recreational facilities, catering to families and individuals alike. Bloomfield's commitment to sustainability is evident in its well-maintained gardens and tree-lined streets, promoting an eco-friendly environment.

Technologically, Bloomfield stands out with its integration of smart technology in urban management. From automated waste collection systems to smart lighting solutions, the city is leveraging technology to enhance the quality of life for its residents. High-speed internet connectivity is widely available, contributing to the growth of the local economy and attracting remote workers and tech startups.

Bloomfield is also renowned for its diverse community, which enhances its cultural landscape. Various community events throughout the year celebrate this diversity, bringing together people from different backgrounds to share their traditions, foods, and arts. The local markets offer an array of artisanal products and fresh produce, highlighting Bloomfield's focus on supporting local businesses and fostering community engagement.

Education plays a crucial role in Bloomfield's development, with several reputable schools and educational institutions located within its borders. The area is not only focused on academic excellence but also emphasizes holistic development, with various extracurricular programs available for students.

Transportation in Bloomfield is well-organized, featuring efficient public transport options that connect residents to neighboring areas and the city center. This accessibility facilitates a seamless commute, making Bloomfield an attractive option for those seeking a balance between suburban serenity and urban convenience.

In summary, Bloomfield 0482, 0412, 0471, 0472, and 0443 exemplify a thriving community that marries tradition with innovation. Its array of features, advanced technologies, and strong sense of community position it as a desirable location for both residents and visitors. As Bloomfield continues to evolve, it remains dedicated to enhancing the quality of life for those who call it home.
Top Page Image Contents