Bloomfield 0482 PLUMBER’S Installation Instructions Automatic Brewers, Water Supply Installation

Page 8

INSTALLATION (continued)

READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION

CAUTION:

ELECTRICAL

DAMAGE

DO NOT plug in or energize this appliance until all Installation Instructions are read and followed. Damage to the Brewer will occur if these instructions are not followed.

IMPORTANT:

Tank must be full of water before connecting brewer to electric power. Heating elements will be damaged if allowed to operate without being fully submerged in water. See instructions for filling tank, page 8.

Damage caused by operating the brewer without water in the tank is NOT COVERED BY WARRANTY.

NOTE: Water supply inlet line must meet certain minimum criteria to insure successful operation of the brewer. Bloomfield recommends 1/4" copper tubing for installation of less than 12 feet and 3/8" for more than 12 feet from a 1/2" water supply line.

NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances.

PLUMBER’S INSTALLATION INSTRUCTIONS (AUTOMATIC BREWERS)

Brewer should be connected to a POTABLE WATER, COLD WATER line. Flush water line before connecting to Brewer.

DO NOT use a saddle valve with a self-piercing tap for the water line connection. Such a tap can become restricted by waterline debris. For systems that must use a saddle tap, shut off the main water supply and drill a 3/16” (minimum) tap for the saddle connection, in order to insure an ample water supply. Remember to flush the line prior to installing the saddle.

The brewer must be installed on a water line with average pressure between 20 PSI and 90 PSI. If your water pressure exceeds 90 PSI at anytime, a pressure regulator must be installed in the water supply line to limit the pressure to not more than 90 PSI in order to avoid damage to lines and solenoid.

A water shut-off valve should be installed on the incoming water line in a convenient location (Use a low restriction type valve, such as a 1/4-turn ball valve, to avoid loss of water flow thru the valve.

NSF requires that the brewer be able to be moved for cleaning underneath. Loops of copper tubing will satisfy this requirement. See Figure 3 below.

Fig. 3 Water Supply Installation

In some areas, local codes require a backflow preventer (check valve) to be installed on the inlet water line. If a backflow preventer is used, you must install a water hammer arrester in the incoming line, between the backflow preventer and the brewer inlet, as far away from the brewer as space will allow. This will relieve the excessive back pressures that can cause faucet leaks and solenoid malfunctions.

685 77110 Owners Manual Horizon™ Brewers

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 685 Warranty Statement Applicability Table of ContentsSpecifications Features and Operating Controls Automatic Brewers Features and Operating Controls POUR-OVER Brewers Precautions and General Information Agency Listing InformationElectrical Damage Burn HazardUnstable Equipment Hazard InstallationLeveling the Unit PLUMBER’S Installation Instructions Automatic Brewers Water Supply InstallationELECTRICIAN’S Installation Instructions Shock HazardOperation START-UPPrepare for Next Brew Brewing CoffeePreparation Cleaning Instructions Procedure Clean Coffee BrewerTroubleshooting Suggestions Symptom Possible Cause Suggested RemedyShock Hazard Warmer Plates Access PanelsServicing Instructions Temperature Adjustment Servicing InstructionsTimer Adjustment Automatic Brewers only Remove Tank LID AssemblyReplace Thermostat Cotherm Replace Heating ElementClean Solenoid Screen Replace SolenoidRepair HOT Water Faucet Replace Timer AssemblyReplace HOT Water Faucet Coil Procedure Delime the Water Tank Chemical Burn HazardExploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Service Kits Faucet Repair KitsWiring Diagram Wiring Diagram Telephone Fax

0472, 0482, 0471, 0443, 0412 specifications

Bloomfield, a prominent urban area within Australia, is recognized for its unique postcode identifiers: 0482, 0412, 0471, 0472, and 0443. Each of these postcodes represents dynamic regions that showcase a blend of historical significance and modern advancement, making Bloomfield a vibrant place to live and visit.

At the heart of Bloomfield lies a robust infrastructure that supports both residential and commercial activities. The area is characterized by its extensive green spaces, parks, and recreational facilities, catering to families and individuals alike. Bloomfield's commitment to sustainability is evident in its well-maintained gardens and tree-lined streets, promoting an eco-friendly environment.

Technologically, Bloomfield stands out with its integration of smart technology in urban management. From automated waste collection systems to smart lighting solutions, the city is leveraging technology to enhance the quality of life for its residents. High-speed internet connectivity is widely available, contributing to the growth of the local economy and attracting remote workers and tech startups.

Bloomfield is also renowned for its diverse community, which enhances its cultural landscape. Various community events throughout the year celebrate this diversity, bringing together people from different backgrounds to share their traditions, foods, and arts. The local markets offer an array of artisanal products and fresh produce, highlighting Bloomfield's focus on supporting local businesses and fostering community engagement.

Education plays a crucial role in Bloomfield's development, with several reputable schools and educational institutions located within its borders. The area is not only focused on academic excellence but also emphasizes holistic development, with various extracurricular programs available for students.

Transportation in Bloomfield is well-organized, featuring efficient public transport options that connect residents to neighboring areas and the city center. This accessibility facilitates a seamless commute, making Bloomfield an attractive option for those seeking a balance between suburban serenity and urban convenience.

In summary, Bloomfield 0482, 0412, 0471, 0472, and 0443 exemplify a thriving community that marries tradition with innovation. Its array of features, advanced technologies, and strong sense of community position it as a desirable location for both residents and visitors. As Bloomfield continues to evolve, it remains dedicated to enhancing the quality of life for those who call it home.
Top Page Image Contents