Antunes, AJ VCT-1000 owner manual Troubleshooting

Page 16

VERTICAL CONTACT TOASTER

TROUBLESHOOTING (continued)

Problem

Possible Cause

Corrective Action

Product is overly-toast-

Temperature set too high.

Set temperature control to a lower setting.

ed or Platen heat is too

 

 

Bun Thickness Compression

Measure bun thickness and set Bun Thickness

high or drop time is too

Knobs set improperly.

Compression Knobs correctly (Figure 7).

slow.

 

 

Buns sticking on Release Sheet.

Clean or replace Release Sheet according to the pro-

 

 

 

cedure in the Maintenance section of this manual.

 

Conveyor Cover Assembly not

Re-install Conveyor Cover Assembly.

 

installed properly.

 

 

Loose sprocket setscrews.

Check drive chain for kinks, broken or bent links,

 

 

or other damage. Check motor sprocket and drive

 

 

sprockets; tighten setscrew on flat of shaft if required.

 

 

Check for damaged/worn sprocket and replace as

 

 

required.

 

Conveyor Belt Chain too loose.

Adjust Conveyor Belt Chain length as described in the

 

 

Maintenance section of this manual.

 

Spring Tensioner Assembly or

Replace Spring Tensioner Assembly or Roller

 

Roller Tensioner is damaged or

Tensioner if damaged or missing.

 

missing.

 

Product is under toast-

Bun Thickness Compression

Measure bun thickness and set Bun Thickness

ed or Platen heat is too

Knobs set improperly.

Compression Knobs correctly.

low or drop time is too

 

 

Wiring problem.

Contact your maintenance person or Authorized

fast.

 

Service Agency for service.

Inoperable Thermostat.

 

Conveyor Drive Motor inoper-

 

 

able or incorrect conveyor motor

 

 

installed in toaster.

 

Product is getting

Bun Thickness Compression

Measure bun thickness and set Bun Thickness

stuck or Conveyor Belt

Knobs Set improperly.

Compression Knobs correctly.

Chains stop when prod-

 

 

Release Sheet not cleaned

Clean or replace Release Sheet as described in the

uct is toasting.

properly or is missing.

Maintenance section of this manual..

 

Conveyor Drive motor inopera-

Contact your maintenance person or Authorized

 

tive or incorrect conveyor motor

Service Agency for service.

 

installed in toaster.

 

 

Conveyor Drive Chain loose,

Check drive chain for kinks, broken or bent links,

 

worn, or broken. Loose motor

or other damage. Check motor sprocket and drive

 

drive sprocket.

sprockets, tighten setscrew on flat of shaft if required.

 

 

Check for damaged/worn sprockets and replace as

 

 

required.

 

Conveyor Belt Chain too loose.

Adjust Conveyor Belt Chain length as described in the

 

 

Maintenance section of this manual.

 

Spring Tensioner Assembly or

Replace Spring Tensioner Assembly or Roller

 

Roller Tensioner is damaged or

Tensioner if damaged or missing.

 

missing.

 

16

P/N 1010807 Rev. E 06/06

Image 16
Contents Vertical Contact Toaster Table of Contents Owner InformationService/Technical Assistance Owner InformationImportant Safety Information Important Safety Information SpecificationsElectrical Cord & Plug Configurations Electrical RatingsSpecifications DimensionsUnpacking InstallationAssembling the Unit Installation Installing the Optional Belt Wraps and Roller TensionersEquipment Setup Operation Safety FeaturesOperating Instructions Maintenance DailyMaintenance Replacing the Release Sheet Every 4 6 weeksConveyor Belt Chains Removing Conveyor Belt ChainReplacing the Spring Tensioners Replacing the Optional Roller TensionersMeasuring the Optional Roller Tensioners Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Wiring Diagram Pictorial Wiring Diagram VCT-1000Replacement Parts Parts IdentificationReplacement Parts Vertical Contact Toaster 1010807 Rev. E 06/06 Description Qty Optional Parts VCT-1000 Mechanical Butter Wheel Kit ModelLimited Warranty