Bosch Appliances SHX5AL To Start Unit, To Cancel the Cycle, To Turn the Extra Dry Heat On or Off

OPERATING THE SHX3AM, SHX5AL, & SHX6AP

WARNING

You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped.

To Start Unit:

•Door must be open. Press the “ON/OFF” button to turn the unit on.

•One of the Wash Cycle Indicator Lights will be flashing to show you are in the Wash Cycle selection mode.

•Press the “<” or “>” button to select the desired wash cycle.

•Press the “START” button (Wash Cycle Indicator Light will stop flashing)

•Close the door to start the cycle

Note: Rinse Agent Indicator Light will be illuminated if the unit needs Rinse Agent.

Note: If you close the door without pressing the start button the unit will beep.

To Cancel the Cycle:

•Open the door just far enough to expose the controls. Be careful of water Splash Out!

•Press and hold the “START/RESET” button until the “Active” Indica- tor Light goes out.

•Close the door and wait for about 1 minute for the dishwasher to drain.

•Open the door and press the “ON/OFF” button.

•You are now ready to start a new cycle.

Setting Options (Rinse Agent Amount / Extra Dry Heat Activation / Cycle Completion Signal Tone Level)

•Door must be open. Press the “ON/OFF” button to turn the unit on.

•One of the Wash Cycle Indicator Lights will be flashing to show you are in the Wash Cycle selection mode.

•To enter the Options Setup Mode, press and hold down the “>” button, then press and release the “START RESET” button, then release the “>” button.

•The “Clean” Indicator Light and at least one addition Indicator Light will be flashing to show you are in the Options Setup Mode.

•Press the “>” button to select the option you would like to ad- just.

oIf the “CLEAN” and “RINSE AGENT” Indicator Lights are flashing you are ready to set the amount of Rinse Agent the unit will dispense.

oIf the “CLEAN” and “SANITIZED” Indicator Lights are flashing you are ready to turn your Extra Dry Heat option on/off.

oIf the “CLEAN” and “SANITIZED” and “RINSE AGENT” Indicator Lights are flashing you are ready to set the Cycle Completion

Signal Tone Level.

To Set the Amount of Rinse Agent Dispensed

NOTE: If your glasses have spots you need more Rinse Agent. If your glasses have streaks you need less Rinse Agent.

•With the “CLEAN” and “RINSE AGENT” Indicator Lights flashing.

•Press the “<” button to change the amount of Rinse Agent Dis- pensed.

•As you press the “<” button you will notice the Wash Cycle Indica- tor Lights illuminating.

■If none of the Wash Cycle Indicator Lights are illuminated, the Rinse Agent Dispenser is turned off.

■If one of the Wash Cycle Indicator Lights are illuminated, the Rinse Agent Dispenser is set to deliver the lowest charge of Rinse Agent.

■If two of the Wash Cycle Indicator Lights are illuminated, the Rinse Agent Dispenser is set to deliver a medium charge of Rinse Agent.

■If three of the Wash Cycle Indicator Lights are illuminated, the Rinse Agent Dispenser is set to deliver the largest charge of Rinse Agent.

•Press “START” to save your settings.

To Turn the Extra Dry Heat On or Off

•With the “CLEAN” and “SANTITIZED” Indicator Lights flashing.

•Press the “<” button to change the Extra Dry Heat setting.

•As you press the “<” button you will notice the Wash Cycle Indica- tor Lights illuminating.

oIf none of the Wash Cycle Indicator Lights are illuminated, the Extra Dry Heat option is turned off.

oIf one of the Wash Cycle Indicator Lights are illuminated, the Extra Dry Heat is turned on.

•Press “START” to save your settings.

To Set the Cycle Completion Signal Tone Level

•With the “CLEAN” and “SANITIZED” and “RINSE AGENT” Indicator Lights flashing.

•Press the “<” button to change the Cycle Completion Signal Tone

Level.

•As you press the “<” button you will notice the Wash Cycle Indi- cator Lights illuminating and the Cycle Completion Signal Tone level changing.

oIf none of the Wash Cycle Indicator Lights are illuminated, there will be no tone. The Cycle Completion Signal is turned off.

oIf one of the Wash Cycle Indicator Lights are illuminated, there will be a low Cycle Completion Signal Tone Level.

oIf two of the Wash Cycle Indicator Lights are illuminated, there will be a medium Cycle Completion Signal Tone Level.

oIf three of the Wash Cycle Indicator Lights are illuminated, you will be at the maximum Cycle Completion Signal Tone Level.

•Press “START” to save your settings.

11