Bosch Appliances SHE5AL Out of the dishwasher. Open the Door Carefully during any, Have stopped

OPERATING THE: SHE4AM0

•You are now ready to start a new cycle

Note: You cannot cancel a cycle with the Child Lock feature activated.

Setting Options (Rinse Agent Amount / Extra Dry Heat Activa- tion)

			• Door must be closed. Press the “ON/
SHE4AM1			OFF” button to turn the unit on.
			• One of the Wash Cycle Indicator Lights
			will be flashing to show you are in the
			Wash Cycle selection mode.
			• To enter the Options Setup Mode,
			press and hold down the “>” button,
			then press and release the “START RE-
	WARNING	SET” button, then release the “>” button.
		• The “Clean” Indicator Light and at least one addition Indicator Light
You could be seriously scalded if you allow hot water to splash
		will be flashing to show you are in the Options Setup Mode.
out of the dishwasher. OPEN THE DOOR CAREFULLY during any
		• Press the “>” button to select the option you would like to adjust
wash or rinse cycle. Do not fully open the door until water noises
		o	If the “CLEAN” and “RINSE AGENT” Indicator Lights are flashing
have stopped.
To Start Unit:			you are ready to set the amount of Rinse Agent the unit will
			dispense.
• Door must be closed. Press the “ON/OFF” button to turn the unit		o If the “CLEAN” and “SANITIZED” Indicator Lights are flashing you
	on.
			are ready to turn your Extra Dry Heat option on/off.
•	One of the Wash Cycle Indicator Lights will be flashing to show	To Set the Amount of Rinse Agent Dispensed
	you are in the Wash Cycle selection mode.
		NOTE: If your glasses have spots you need more Rinse Agent. If your
• Press the “<” or “>” button to select the desired wash cycle.
		glasses have streaks you need less Rinse Agent.
•	If desired select the “HALF LOAD” or DELAY START” features at	• With the “CLEAN” and “RINSE AGENT” Indicator Lights flashing.
	this point.
		•	Press the “<” button to change the amount of Rinse Agent Dis-
	o If you would like to delay the start time of the dishwasher press
		pensed.
	the “DELAY” button until the desired delay time (3/6/9 hrs.)
		• As you press the “<” button you will notice the Wash Cycle Indica-
	shows on the Indicator Lights.
	o In addition to your Wash Cycle selection, for small loads of	tor Lights illuminating
		o	If none of the Wash Cycle Indicator Lights are illuminated, the
	lightly soiled dishes press the “HALF LOAD” button. This will
	save energy and water (SHE4AM1# only).		Rinse Agent Dispenser is turned off.
•	Press the “START” button to begin the cycle (Wash Cycle Indica-	o	If one of the Wash Cycle Indicator Lights are illuminated, the
	tor Light will stop flashing and the “Active” Indicator Light will		Rinse Agent Dispenser is set to deliver the lowest charge of
	illuminate)		Rinse Agent.
Note: Rinse Agent Indicator Light will be illuminated if the unit needs		o	If two of the Wash Cycle Indicator Lights are illuminated, the
Rinse Agent.			Rinse Agent Dispenser is set to deliver a medium charge of
Child Lock			Rinse Agent.
		o	If three of the Wash Cycle Indicator Lights are illuminated, the
• After pressing the “START” button you can activate the Child Lock
			Rinse Agent Dispenser is set to deliver the largest charge of
	feature.
			Rinse Agent.
• Press and hold down the “<” button until Child Lock Indicator Light		• Press “START” to save your settings.
	illuminates (Light goes out when button is released).
		To Turn the Extra Dry Heat On or Off
• Now any button you press (except ON/OFF) will not function and
		• With the “CLEAN” and “SANTITIZED” Indicator Lights flashing.
	the Child Lock Indicator Light illuminates when pressing.
•	To deactivate, press and hold the “<” button until the Child Lock	• Press the “<” button to change the Extra Dry Heat setting.
	Indicator Light goes out.	• As you press the “<” button you will notice the Wash Cycle Indica-
To Cancel the Cycle:		tor Lights illuminating
• Press and hold the “START/RESET” button until the “Active” Indica-		o	If none of the Wash Cycle Indicator Lights are illuminated, the
	tor Light goes out.		Extra Dry Heat option is turned off.
• Wait for about 1 minute for the dishwasher to drain.		o	If one of the Wash Cycle Indicator Lights are illuminated, the
• Press the “ON/OFF” button.			Extra Dry Heat is turned on.

• Press “START” to save your settings.

13