Bosch Appliances SHE44C manual Delay Start, Cycle Completion Signal, Starting the Dishwasher

	Wash Cycle Options
	Top Rack Only or Half Load	Extra Dry Heat	Delay Start	Cycle Completion Signal	OPTIDRYTM	ECO
SHE46C	x	x	19h		x
SHE44C		x			x
SHU43C		x
SHE56C		x	19h		x
SHE47C	x	x	24h		x
SHX46L	x	x	19h	x	x
SHX43E				x
SHX46A	x			x
SHV46C	x			x
SHE45C		x			x
SHX45C	x			x
SHE43M			19h
SHX43M			19h	x
SHE45M	x	x	19h		x
SHV45M	x	x	19h	x
SHX45M	x	x	19h	x	x
SHE55M	x	x	19h		x	x
SHE43F		x

Figure 19

Exposed Front Controls

1) Close the door

2) Turn on
	3) Select a cycle

4)The unit will then start

Figure 20

Hidden Top Controls

1) Open the door

·When the LED display shows a “00” or a “01” release both buttons.

·To enable the Additional Drying Heat, press the left “Cancel Drain” button until the LED display shows a “01”.

·To disable the Additional Drying Heat, press the left “Cancel Drain” button until the LED display shows a “00”.

·Press the On/Off button to save the setting.

Delay Start

This option allows you to delay the start time of your dishwasher.

To activate:

·Turn the dishwasher on.

·Select the desired wash cycle.

·Press and hold the Delay Start button. Release when the desired delay time is shown in the display window.

The Cycle Completion Signal

This Cycle Completion Signal is a tone that sounds to alert you when your dishwasher finishes washing and drying your dishes. You can either disable the tone or set the volume.

To activate:

·Press and hold the right “Cancel Drain” button then press and hold the On/Off button.

·When the light on the “Cancel Drain” button you are pressing illuminates and the tone begins to sound, release both buttons.

·Press the right-most “Cancel Drain” button until the tone is either at the desired volume or is silent.

·Press the On/Off Button. The Cycle Completion Signal is now set.

OPTIDRY™

This feature senses when the unit is low on rinse agent and automatically increases the drying time. For best performance, always use a liquid rinse agent even if your detergent contains a drying additive.

ECO function (select models): This option saves energy by reducing water temperature.

Starting the Dishwasher

To start the dishwasher, follow the instructions in Figures 19 and 20 depending the control location.

Interrupting a Cycle

NOTE: Should you need to interrupt a cycle (to add or remove an item, to add detergent, etc.), it is best to do so within the first 30 minutes of the cycle.

Exposed Front Controls (See Figure 19)

1.Press the On/Off button to turn the unit off.

2.Wait at least ten seconds or until the water noises stop before opening the dishwasher door.

3.To resume the cycle, close the dishwasher door and then press the On/Off button.

Hidden Top Controls (See Figure 20)

1.Open the dishwasher door just far enough to expose the control panel.

2.Press the On/Off button to turn the unit off.

3.Wait at least ten seconds or until the water noises stop before opening the dishwasher door.

4.To resume the cycle, press the On/Off button and close the dishwasher door.

2) Turn on

3) Select a cycle

4)Close the door to start

WARNING

You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped.

Wait at least ten seconds or until water noises stop before opening the dishwasher door. To

14