Maytag JDB1060AW, MDB8750AW, MDB9750AW manual Checking Valve Operation, Air Water Inlet and Vent

Page 41

Service and Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit and discharge capacitor through a 10,000 ohm resistor before attempting to service, unless test procedures require power to be connected. Ensure all ground wires are connected before certifying unit as repaired and/or operational.

Checking Valve Operation

 

No Fill

 

1. Disconnect power to the machine.

 

2. Remove Support and Toe Panel. (See paragraph Front

 

Support and Toe Panel removal).

 

3. Remove wires from Valve Solenoid.

 

4. Perform continuity check across terminals of

 

Solenoid. If NO continuity is present, replace Water

 

Valve.

 

Alternate Test: Use Motor Test Cord hooked directly to

Air Water Inlet and Vent

the Valve Solenoid. Turn water supply on

The Air Water Inlet is located on the left side of the Tub,

and plug in test cord. If NO water is

present, replace Water Valve.

and mounted to the exterior of Tub. Removal of the Air

 

Water Inlet and Vent requires the removal of the

Overfill

Dishwasher from under the counter. Vent only operates if

cabinet becomes pressurized and will open flap on top of

 

If Water Valve allows water to flow without power to Valve

Air Water inlet.

Removal

Solenoid, replace the Water Valve.

 

NOTE: The Water Valve is a non-repairable component.

1. Disconnect power to the machine.

 

The only servicing required is to clean the Inlet

2. Remove the Air Water Inlet Cover located on the left

Screen if needed.

inside wall of Tub. Pull cover straight out to remove.

 

Inlet Screen

3. Carefully pull back insulation from the left side of the

Sediment on the Inlet Screen can hinder water flow

Tub.

4. Remove rubber hose from channel in Tub, or slip off of

through the Water Valve.

fitting on inlet.

 

5. Grasp upper portion of the Air/Water Inlet. Pull and

Cleaning

rotate the Air/Water Inlet clockwise to release it from

 

the Tub.

1.Disconnect power to the machine.

2.Remove Water Valve from the Dishwasher (See Water Valve Removal).

3.Remove 4 screws securing valve body to Water Inlet Mounting Bracket.

4.Clean screen.

NOTE: Make sure to reattach the ground wire to the mounting bracket.

41

16022783 Rev. 0

©2004 Maytag Appliances Company

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Service Important Information Customer Service Support CenterTable of Contents Important Safety Information Precaución SSI Appliance Test Meter Electrical Equipment & TestingElectrical Test Equipment Grounding and Polarity Motor Test CordWax Motor Check Electrical TestsCycles Cycles & OptionsOption Description Display Description ENN-AIR Overflows Electrical-Mechanical TroubleshootingWill Not Fill Will Not Drain Poor WashabilityContinues To Drain Poor DryingWater Leaks Electrical Mechanical TroubleshootingNoise Will Not Start Or ProgramWill Not Wash Field Service TestWill Not Dry Manual Function TestTroubleshooting Flow Chart Flow Chart Troubleshooting Troubleshooting Flow Chart Chart Troubleshooting Flow Chart From Customer Instruct Issue Troubleshooting Troubleshooting From Front Support and Toe Panel Removal Removal Disconnect power to the machineDetergent / Rinse Dispenser Mechanism and Reservoir Checking Operation Disconnect power to the machineInner Door Panel Wax Motor Detergent / Rinse Dispenser Wire CoverSwitch Removal Disconnect power to the machine Door Latch & Switch Holder AssemblyControl Panel PC BoardRemoval ReplacementOuter Door Above Door SpringDoor Hinge and Support Top Wash Arm Door Spring and Component Replacement Over Pressure FilterLower Wash Arm Manifold Docking StationFloat To Check Float Switch Disconnect power to the machineHeating Element To Check Heating Element Disconnect power to the machineRemoval Wattage Checks Disconnect power to the machine Water Valve ThermostatsAir Water Inlet and Vent Checking Valve OperationUpper Rack Removal Tub WheelsTurbidity Sensor Drain Pump Wash Motor Assembly16022783 Appendix a Built-In Dishwasher Page Built-In Dishwasher Lavavajillas Empotrado Lave-vaisselle encastré Sound Seals Select models only Selladores de ruido 34 1/ 4 34 5/ 8 1 3 / 8 35 1 3 13B Ground IMPORTANT/IMPORTANTE 38A 39A

JDB1060AW, JDB1100AW, JDB2100AW, JDB2150AWP, MDB9750AW specifications

Maytag is a trusted name in home appliances and their line of dishwashers is no exception. Models like the JDB1060AW, JDB2150AWP, JDB1100AW, MDB9750AW, and MDB8750AW highlight a range of impressive features designed to make dishwashing efficient and hassle-free.

The Maytag JDB1060AW is equipped with a powerful motor and a specific set of wash cycles that handle everything from light loads to pots and pans. Its Extra Power button ensures that stubborn stains are tackled with high-temperature wash, while the stainless steel tub provides durability and aids in moisture control. The design is straightforward, making it user-friendly for those who want straightforward functionality.

The JDB2150AWP takes efficiency a step further with an energy-efficient design that helps save on water and power bills. Its unique Quad-Clean wash system utilizes multiple wash arms to ensure that every dish is thoroughly cleaned, leaving no corner untouched. Additionally, it features a delay start option that allows users to set their washing cycle to begin at a more convenient time, maximizing convenience.

Moving to the JDB1100AW model, it emphasizes noise reduction technology. With a sound rating of only 50 dBA, it operates quietly, making it ideal for open-concept living spaces. This model also incorporates a Wash Zone feature, focusing cleaning power where it’s needed most, perfect for lightly soiled dishes while saving water.

The MDB9750AW model is a powerhouse of cleaning, thanks to its PowerBlast scrubber. This feature efficiently tackles tough, stuck-on food, making it a time-saver for busy households. The Stainless Steel Inner Door ensures a sleek look and adds to the dishwasher’s overall resistance to wear over time.

Lastly, the MDB8750AW model incorporates the advanced Sensor cycle technology. This smart feature automatically adjusts the wash cycle based on how dirty the dishes are, optimizing water and energy usage. Its high-capacity design allows you to wash more dishes in one go, and with the addition of a soil sensor, it adapts to cleaning needs with ease, delivering a repeatable high-level performance.

All these Maytag models emphasize reliability, efficiency, and the latest cleaning technologies, ensuring that busy families have their dishwashing needs met without hassle. Each model embodies a commitment to quality and performance, providing consumers with solid options for their kitchen needs.
Top Page Image Contents