Extron electronic USP 405 IR 801 Infrared Remote Control, Selecting an input, Freezing an input

Page 37

IR 801 Infrared Remote Control

The optional IR 801, shown at right, replicates all of the front panel controls except the Menu and Next buttons. If Executive mode is enabled, selections and adjustments can still be made using the IR 801, but you must use the USP 405’s front panel or the Windows-based control program (via an RS-232 device) to configure and program the USP. See chapter 3, “Serial Communication”, for details.

While Executive mode is active, adjustments can still be made using the IR 801.

The topmost part of the IR 801 features three aspect ratio preset buttons, a horizontal filters button, a freeze button, and a vertical filters button.

The horizontal and vertical filtering apply only to the following input formats:

Input 1: RGB

Input 2: RGB, YUVp, HDTV

The middle portion of the IR 801 features five input selection buttons, the size buttons for sizing an image, and the shift buttons for centering an image.

The bottom portion of the IR 801 contains the adjustment controls for color, tint, brightness, contrast, detail, and zoom adjustments.

Selecting an input

To use the IR 801 to select an input, press the button corresponding to the input number.

Freezing an input

To freeze the input being displayed, press the Freeze On/Off button. To unfreeze the input, press the Freeze button again.

Aspect ratio presets

Up to three saved memory presets may be recalled by pressing one of the three Aspect ratio preset buttons. Sizing and centering information are saved with the presets.

USP 405 • Installation and Operation 2-21

Page 36 Page 38
Image 37
Page 36 Page 38
Contents USP Universal Signal ProcessorConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolRear panel video outputs Rear panel video inputs NUSP 405 Quick Start QS-1 Main menu Default Cycle menuInput menu QS-2 USP 405 Quick StartAdvanced Configuration menu Memory Presets menuOutput menu USP 405 Quick Start QS-3Executive Mode menu Picture Adjustments menuGenlock menu Exit menuUSP 405 Quick Start QS-5 StepQS-6 USP 405 Quick Start Replaced with a detail sharpness adjustmentTable of Contents Table of Contents, cont’d USP 405 Table of Contents Iii Serial Digital Interface SDI Card InstallationIv USP 405 Table of Contents One About this Manual Features and OptionsAbout the USP Six video outputs Introduction, cont’d Options and accessoriesInstallation and Operation Mounting the Scaler Application diagramsTabletop use Rack mountingExample of the USP 405 being used as a scaler Example of the USP 405 being used as a scan converterPower connection Rear Panel FeaturesUSP 405 rear panel connectors Video input and output connectionsConnectors 14 and 15 output the same signal simultaneously Genlock connections Front Panel FeaturesRS-232 connection Input selection buttons Picture adjustment buttonsUSP 405 front panel Genlock setup Genlock and Vertical Interval SwitchingLCD menu display and controls Timing Source Superimposed waveforms Oscilloscope displaysVectorscope screen during horizontal phase adjustment Setting up a DVD sourceVectorscope screen during color subcarrier phase adjustment Optimizing the SystemMoving through menus by using front panel controls Menus, Configuration, and AdjustmentsDefault menus Menu overviewMain menus Input ConfigurationInput Phase submenu Output ConfigurationResolution and refresh rates submenu Input #2 submenuMemory Presets Recalling a preset Erase memory presets submenuBlue Mode submenu Advanced ConfigurationEdge Smoothing submenu Encoder Filter submenuGenlock menu Exit menu Image AdjustmentsAdjust knobs have no mechanical limits to their rotation Front Panel Security Lockout Executive modeAspect ratio presets IR 801 Infrared Remote ControlSelecting an input Freezing an inputAdjusting image size TroubleshootingImage adjustments Horizontal and vertical filteringProblem Cause Solution Operating problemsInstallation and Operation, cont’d Three Signal processor-initiated messages Host-to-signal processor communicationsError responses RS-232 Programmer’s GuideSymbol definitions Using the command/response tablesAscii to Hex conversion table Serial Communication, cont’d Command Ascii Command Response Additional descriptionFreeze Pixel phase Command Ascii Command Response Values Command/response table for special function SIS commandsUsing the control program Installing the softwareControl Software for Windows Installing the software Using the help programUsing the software Labeling Buttons on the USPButton label screen Installing labels in the USP 405’s buttonsVCR Setting the Output Rate Using the Per Input FeatureSerial Communication, cont’d AAppendix USP 405 Appendix SpecificationsSync Accessories Part Numbers and AccessoriesAccessories Part number Included partsRemoving the USP 405 cover Firmware Upgrade InstallationLocating the four firmware IC chips U24 U60 U68U67Both SDI cards installed Serial Digital Interface SDI Card InstallationSDI input card standoff SDI output card circuit board connectorOutput SDI board installation Input SDI board installationInstalled SDI output card Installed SDI input cardFCC Class a Notice Extron’s Warranty Extron Electronics, USA
Related manuals
Manual 3 pages 46.42 Kb

USP 405 specifications

The Extron Electronics USP 405 is a versatile and high-performance solution designed specifically for managing audio and video signals in varied settings, including classrooms, conference rooms, and other collaboration spaces. This compact device excels in providing seamless connectivity, enhanced audio, and video quality, making it an essential component for modern AV system integration.

One of the key features of the USP 405 is its ability to support multiple input formats. With a blend of HDMI, DisplayPort, and analog video inputs, it offers unmatched flexibility for connecting various devices such as laptops, tablets, and other multimedia equipment. This ensures users can easily share content without worrying about compatibility issues.

Equipped with advanced signal processing technologies, the USP 405 enhances both video and audio performance. The device includes sophisticated scaling capabilities that automatically adjust the resolution of the video output to match the display device specifications, ensuring optimal viewing experiences. Additionally, the built-in audio embedding and de-embedding features allow for seamless integration of audio sources, enhancing clarity and reducing wiring complexity.

Another standout characteristic of the USP 405 is its intuitive user interface. The front panel features clearly labeled controls for easy operation, while the device can also be controlled via network protocols. This means it can be integrated into existing control systems and managed remotely, streamlining AV operations.

The USP 405 also incorporates Extron's renowned signal integrity technologies, which help maintain high-quality signal transmission over long distances. This ensures that audio and video remain clear and reliable, even in larger setups where cable runs can be extensive.

Durability and reliability are crucial in any AV setup, and the USP 405 is built to withstand the rigors of daily use. Its robust design and fanless architecture reduce potential points of failure while ensuring quiet operation, making it an ideal choice for noise-sensitive environments.

In conclusion, the Extron USP 405 provides a comprehensive suite of features aimed at enhancing AV performance and integration. With its multiple input types, advanced signal processing, user-friendly control options, and durable design, it stands out as a powerful tool for any modern AV installation. Whether in educational settings, corporate environments, or entertainment venues, the USP 405 helps create engaging and productive audiovisual experiences.
Top Page Image Contents