Bunn Complete Guide to Programming Your H5X Water Heater
Page 7

PROGRAMMING (Continued)

LEVEL 2 PROGRAMMING

FAHRENHEIT OR CENTIGRADE SELECTION, & RESTORING FACTORY DEFAULTS

1.To enter Level 2 Programming, press and hold the center button until H2 appears on the display (approximately 6 seconds). Release the center button, The display will show either FAH (Degrees in Fahrenheit) or CEn (Degrees in Centigrade).

2.Press and release the (+) or (-) buttons to alternate between FAH and CEn.

3.After setting FAH or CEn, to exit Level 2 Programming, press and release the center button twice. Software Version will show on the display, then (-).

RESTORING FACTORY DEFAULTS

1.To restore Factory Defaults (This clears all settings that were previously entered), press and release the center button until H2 appears on the display (approximately 6 seconds). Release the Center Button, then press and release the Center Button once more. The display will read H3, then show (- - -).

2.Press and hold both (+) and (-) buttons to initiate the resetting of the factory de- fault settings. The display (- - -)will flash on and off during this time (about 5 to 7 seconds).

3.When the factory default numbers are loaded in, the display will stop flashing, then read don (DONE). You can now release the two buttons.

NOTE: If you release the two buttons at any time before the display reads don, the Factory Default numbers will not be entered. The old numbers will remain in the memory.

4.To exit Level 2 Programming press and release the center button once more. The display will show the Soft- ware Version, then (-).

7

10420.1 040309

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents H5E, H5X BUNN-O-MATIC Commercial Product Warranty Introduction ContentsUser Notices CE Requirements Electrical RequirementsElectrical Hook-Up Initial SET-UP Plumbing RequirementsPlumbing Hook-Up Level 1 Programming ProgrammingLevel 2 Programming Restoring Factory DefaultsSupport for Large Receptacles CleaningWall Mounted Installation Draining the DispenserProblem Probable Cause Remedy TroubleshootingFlashes Equipment will not Operate Safety overflow switch Water boils continuously Temperature control Component Access ServiceLocation Service Electronic ControlsLiquid Level Control Test Procedure H5X Thermostat Wiring Connections Test Procedure Service Limit ThermostatSafety Overflow Switch Service Safety Overflow SwitchSolenoid Valve Service Solenoid ValveTank Heater Service Tank HeaterSchematic Wiring Diagram H5E Schematic Wiring Diagram H5X Volts AC RED Schematic Wiring Diagram H5XA, H5EA
Related manuals
Manual 9 pages 10.17 Kb Manual 2 pages 44.15 Kb Manual 25 pages 51 Kb Manual 24 pages 29.7 Kb

H5X specifications

The Bunn H5E and H5X coffee machines represent a leap forward in brewing technology, specifically tailored for commercial use. Both models focus on delivering high-quality coffee while maximizing efficiency, making them ideal choices for busy cafés and restaurants.

The Bunn H5E features a unique 5-liter dual tank system, which allows for faster brewing times and reduces wait periods for customers. This dual tank setup facilitates the simultaneous preparation of multiple coffee types, catering to a diverse clientele. The H5X, on the other hand, is equipped with advanced electronic controls that permit precise temperature adjustments to ensure that the ideal brewing conditions are maintained, enhancing flavor extraction.

One of the standout features of both models is the patented BrewOptimized Technology. This technology helps maintain optimal water temperature and consistent flow rates throughout the brewing process, ensuring that each cup of coffee meets the high standards expected in commercial settings. Additionally, the units utilize a patented stainless steel brew basket that enhances durability and simplifies cleaning, making maintenance less of a chore for busy staff.

Another significant characteristic of the H5E and H5X is their programmable settings, which allow operators to customize brewing parameters according to their specific preferences or customer needs. This flexibility means that establishments can experiment with various coffee profiles, ensuring that they serve only the best products to their patrons.

Safety is also a priority in the design of these machines. The H5E and H5X come equipped with built-in safety features such as automatic shut-off and thermal overload protection, which help to prevent accidents and enhance longevity. Moreover, their compact design allows for easy installation in a variety of settings, whether it's a small coffee stand or a large restaurant operation.

Both the Bunn H5E and H5X models are energy-efficient, with features that minimize power consumption without compromising performance. This focus on sustainability not only helps reduce overhead costs but also appeals to environmentally conscious consumers.

In summary, the Bunn H5E and H5X coffee machines are engineered for high performance, reliability, and versatility. With features designed to provide quick, quality coffee while ensuring ease of operation and maintenance, these machines are ideal for any establishment that takes its coffee seriously. Whether you’re brewing for a crowd or crafting specialty drinks, the H5E and H5X stand ready to deliver excellent results every time.
Top Page Image Contents