Bunn TNT-3, TNTF-3 manual Iced TEA Brew Timer

Page 21

SERVICE (cont.)

BREW TIMER (ICED TEA - LATE MODELS)

 

NEW STYLE

 

FIG. 12 ICED TEA BREW TIMER

P2213.60

 

Location:

The timer is located in the hood on the right side.

Test Procedure.

NOTE: Do not remove or install wires while timer board is installed. Pressure applied to one side may cause damage to the board.

1.Disconnect the brewer from the power source and remove the front access panel.

2.Remove the two #8-32 screws securing circuit board to the mounting bracket.

3.Remove circuit board and spacers (as required).

4.With a voltmeter, check the voltage across termi- nals TL1 and TL2 when the "ON/OFF" switch is in the "ON" position and the ICED/OFF/HOT switch is in the "ICED" position. Connect the brewer to the power source. The indication must be 120 volts ac for two wire 120 volt models and three wire 120/ 208 volt models.

5.Disconnect the brewer from the power source.

If voltage is present as described, proceed to #6.

If voltage is not present as described, refer to the Wiring Diagrams and check the brewer wiring har- ness.

6.With a voltmeter, check the voltage across termi- nals TL1 and TL4 when the "ON/OFF" switch is in the "ON" position and the ICED/OFF/HOT switch is in the "ICED" position. Connect the brewer to the power source. The indication must be 0 volts.

If voltage is as described, proceed to #7.

If voltage is not as described, disconnect the brewer from the power source and replace the timer.

7.With a voltmeter, check the voltage across termi- nals TL1 and TL4 when the "ON/OFF" switch is in the "ON" position and the ICED/OFF/HOT switch is in the "ICED" position. Connect the brewer to the power source and press the "START" switch. The indication must be as follows 120 volts ac for two wire 120 volt models and three wire 120/208 volt models.

If voltage is present as described, the brew timer is operating properly. Reset the timer as required, to obtain the desired brew volume.

If voltage is not present as described, disconnect the brewer from the power source and replace the timer.

Removal and Replacement:

1.Remove the two #8-32 screws securing circuit board to the mounting bracket.

2.Remove circuit board and spacers (as required).

3.Remove all wires from the timer.

4.Attach all wires to the replacement timer board prior to installation to the component mounting bracket. Refer to FIG. 13 when reconnecting the wires.

5.Install new circuit board with spacers (as re- quired) to the component mounting bracket.

6.Adjust the timer as described below.

Timer Setting:

NOTE: Prior to setting or modifying volumes, check that the brewer is connected to water supply, the tank is properly filled, and a funnel and server are in place. NOTE: All volume settings must be done with the sprayhead installed.

Page 21

28201 081500

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Telephone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisContents WarrantyIntroduction #00831.0000 #00656.0000 #03408.0000 #03409.0000 User NoticesElectrical Requirements Plumbing RequirementsElectrical Hook-Up Initial SET-UP Plumbing RequirementsInitial SET-UP Adjusting Brew VolumesICED/OFF/HOT Switch CleaningStart Switch Operating ControlsTroubleshooting Problem Probable CauseRemedy Problem TroubleshootingBrew cycles will not start Brew Timer RemedyProblem Probable Cause Remedy Probable Cause Remedy Or HOT position Water flows into tank continuously Brew TimerPosition Beverage overflows dispenser DispenserWeak beverage Filter Type Tea Sprayhead Funnel Loading Remove and clean lime off the tank heater. SeeDry tea leaves remain Funnel Brewer is making unusal noises SolenoidsService Component AccessContents Service Brew Solenoid Valve HOT TEASolenoid valve Brew Solenoid Valve Iced TEA HOT TEA Brew Timer Brew Timer HOT TEA Early ModelsIf voltage is as described, proceed to #7 Brew Timer HOT TEA Late ModelsDigital Timer Wiring Service Brew Timer HOT TEA Late MODELScontBrew Timer Iced TEA Early Models Iced TEA Brew Timer Brew Timer Iced TEA Late MODELScont Control Thermostat Test Procedures Disconnect the brewer from the power sourceDilution Solenoid Valve Test Procedure Disconnect the brewer from the power sourceLimit Thermostat Limit ThermostatICED/OFF/HOT Switch ICED/OFF/HOT SwitchStart Switch Start SwitchTank Heater Indication must beEls Thermal Fuse Service Thermal Fuse Models W/Faucet Only28201
Related manuals
Manual 30 pages 36.83 Kb

TNT-3, TNTF-3 specifications

The Bunn TNTF-3 is a high-performance coffee brewer designed for commercial use, specifically suited for busy environments such as restaurants and cafes. This machine seamlessly combines efficiency with quality, making it a popular choice for professionals who demand the best in their equipment.

One of the standout features of the Bunn TNTF-3 is its three warmer plates, which allow users to brew and store multiple batches of coffee simultaneously. This design ensures that there’s always fresh coffee ready for customers, minimizing downtime during peak service hours. Each warmer has its own independent control, providing versatility in temperature settings to accommodate different coffee types and customer preferences.

The Bunn TNTF-3 utilizes a patented SplashGard funnel that helps to keep the brewing process clean and efficient. This technology not only prevents splashes and messes but also improves user safety by protecting operators from hot water and coffee spills. The brewer’s stainless steel construction contributes to its durability, enhancing its longevity in a high-volume setting.

In terms of brewing capabilities, the TNTF-3 can prepare up to 3.8 gallons of coffee per hour, making it ideal for both small and large operations. The machine is equipped with a brew control feature that allows users to customize the strength and flavor of the coffee, ensuring that each cup meets the highest standards. Additionally, the digital timer and brew status light offer convenient monitoring at a glance.

For ease of maintenance, the Bunn TNTF-3 is designed with accessibility in mind. With removable components and straightforward cleaning procedures, operators can keep the machine in top condition without significant downtime. The brewer also features a low-water shut-off system, which helps to protect the unit from damage due to insufficient water levels.

Overall, the Bunn TNTF-3 embodies a blend of innovative technology, practical design, and optimal performance, making it a powerful tool for coffee professionals. Whether it be for daily service or special events, the Bunn TNTF-3 stands out as a reliable coffee brewing solution that consistently delivers rich, flavorful coffee with every batch. Its combination of speed, safety, and quality assurance solidifies its status as a preferred choice in commercial settings.
Top Page Image Contents