Bunn TNTF-3, TNT-3 manual Electrical Requirements, Plumbing Requirements, Electrical Hook-Up

Page 4

ELECTRICAL REQUIREMENTS

CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.

120V model brewers require 2-wire, grounded service rated 120 volt ac, 15 amp, single phase, 60 Hz.

120/208V model brewers require 3-wire, grounded service rated 120/ 208 volt, 20 amp, single phase, 60 Hz.

L2 RED

WHITE

NEUTRAL L1 BLACK

120V.A.C.

208V.A.C.

120V.A.C.

Electrical Hook-Up

CAUTION – Improper electrical installation will damage electronic components.

1.An electrician must provide electrical service as specified.

2.Remove the top lid and rotate the control thermostat knob fully counterclockwise to the "OFF" position.

3.a) 120V brewers have an attached cordset. Plug in the brewer and proceed to #6.

b) 120/208V brewers, feed the cord through the strain refief at the rear of the brewer and connect it to the terminal block.

4.Using a voltmeter, check the voltage and color coding of each conductor at the power source.

5.Connect the brewer to the power source and verify the voltage at the terminal block.

6.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up.

PLUMBING REQUIREMENTS

These brewers must be connected to a cold water system with operating pressure between 20 (138) and 90 psi (620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1⁄4" flare.

NOTE - Bunn-O-Matic recommends 1⁄4" copper tubing for installations of less than 25 feet and 3⁄8" for more than 25 feet from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA)

and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).

Page 4

28201 081500

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Post Office BOX SPRINGFIELD, Illinois Telephone 217 529-6601 FAX 217Warranty ContentsIntroduction User Notices #00831.0000 #00656.0000 #03408.0000 #03409.0000Plumbing Requirements Electrical RequirementsElectrical Hook-Up Plumbing Requirements Initial SET-UPAdjusting Brew Volumes Initial SET-UPCleaning ICED/OFF/HOT SwitchStart Switch Operating ControlsProblem Probable Cause TroubleshootingRemedy Troubleshooting ProblemBrew cycles will not start Brew Timer RemedyProblem Probable Cause Remedy Probable Cause Remedy Water flows into tank continuously Brew Timer Or HOT positionPosition Beverage overflows dispenser DispenserRemove and clean lime off the tank heater. See Weak beverage Filter Type Tea Sprayhead Funnel LoadingDry tea leaves remain Funnel Brewer is making unusal noises SolenoidsComponent Access ServiceContents Brew Solenoid Valve HOT TEA ServiceSolenoid valve Brew Solenoid Valve Iced TEA Brew Timer HOT TEA Early Models HOT TEA Brew TimerBrew Timer HOT TEA Late Models If voltage is as described, proceed to #7Service Brew Timer HOT TEA Late MODELScont Digital Timer WiringBrew Timer Iced TEA Early Models Iced TEA Brew Timer Brew Timer Iced TEA Late MODELScont Test Procedures Disconnect the brewer from the power source Control ThermostatTest Procedure Disconnect the brewer from the power source Dilution Solenoid ValveLimit Thermostat Limit ThermostatICED/OFF/HOT Switch ICED/OFF/HOT SwitchStart Switch Start SwitchIndication must be Tank HeaterEls Service Thermal Fuse Models W/Faucet Only Thermal Fuse28201
Related manuals
Manual 30 pages 36.83 Kb

TNT-3, TNTF-3 specifications

The Bunn TNTF-3 is a high-performance coffee brewer designed for commercial use, specifically suited for busy environments such as restaurants and cafes. This machine seamlessly combines efficiency with quality, making it a popular choice for professionals who demand the best in their equipment.

One of the standout features of the Bunn TNTF-3 is its three warmer plates, which allow users to brew and store multiple batches of coffee simultaneously. This design ensures that there’s always fresh coffee ready for customers, minimizing downtime during peak service hours. Each warmer has its own independent control, providing versatility in temperature settings to accommodate different coffee types and customer preferences.

The Bunn TNTF-3 utilizes a patented SplashGard funnel that helps to keep the brewing process clean and efficient. This technology not only prevents splashes and messes but also improves user safety by protecting operators from hot water and coffee spills. The brewer’s stainless steel construction contributes to its durability, enhancing its longevity in a high-volume setting.

In terms of brewing capabilities, the TNTF-3 can prepare up to 3.8 gallons of coffee per hour, making it ideal for both small and large operations. The machine is equipped with a brew control feature that allows users to customize the strength and flavor of the coffee, ensuring that each cup meets the highest standards. Additionally, the digital timer and brew status light offer convenient monitoring at a glance.

For ease of maintenance, the Bunn TNTF-3 is designed with accessibility in mind. With removable components and straightforward cleaning procedures, operators can keep the machine in top condition without significant downtime. The brewer also features a low-water shut-off system, which helps to protect the unit from damage due to insufficient water levels.

Overall, the Bunn TNTF-3 embodies a blend of innovative technology, practical design, and optimal performance, making it a powerful tool for coffee professionals. Whether it be for daily service or special events, the Bunn TNTF-3 stands out as a reliable coffee brewing solution that consistently delivers rich, flavorful coffee with every batch. Its combination of speed, safety, and quality assurance solidifies its status as a preferred choice in commercial settings.
Top Page Image Contents