Bunn CDBCF Brewing Circuit Problem Probable Cause, Brew cycle will not start Display flashing

Page 17

TROUBLESHOOTING (cont.)

 

 

BREWING CIRCUIT

 

 

PROBLEM

 

PROBABLE CAUSE

Brew cycle will not start

 

1. Display flashing

2. No water

3. No power or incorrect voltage to the brewer

4. ON/OFF switch not in the "ON" position

5. Low water temperature (Brew lockout is enabled)

6. Water not touching refill probe inside tank

7. Switch panel

REMEDY

Brewer has shut down due to malfunction (See Diagnostic Chart in manual, Page 21, or under top lid of brewer).

Water lines and valves to the brewer must be open.

Check for voltage across the black and white terminals at the termi- nal block.

The indicator lamp must be lit

Allow brewer to heat until ready lamp is lit, or disable the brew lockout feature. (See page 8)

Press ON/OFF switch (indicator must be lit). Brewer will refill until water touches probe inside tank. Water must be in contact with refill probe before brew cycle will start.

Disconnect the brewer from the power source. Disconnect the rib- bon connector from the control board. Check for continuity be- tween pins 1 & 2 (An arrow on the connector indicates pin 1). No continuity should be present. Press the BREW switch. Continuity should be present for as long as the switch is held "ON". If no con- tinuity is present, replace the switch membrane decal.(See page 24)

Page 17

35582 041503

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents DIS Vers ION Introduction ContentsBUNN-O-MATIC Commercial Product Warranty User Notices Electrical Hook-Up Electrical RequirementsPlumbing Requirements Brew Switch ON/OFF SwitchReady Indicator Temperature IndicatorsCoffee Brewing Initial SET-UPCleaning POUR-OVER FeatureSetting Brew Temperature CDBC, Single CD Adjustments & Optional SettingsWater Sensing Threshold Adjustment Procedure Adjustments & Optional SettingsPulse Brew Setup Procedure Cdbc & Single CD Before troubleshooting this brewer, check for the following TroubleshootingRemedy TroubleshootingRefill Circuit Problem Probable Cause Fill or refill does not shut OFF ON/OFF Switch on Troubleshooting Refill CircuitWater does not heat to proper temperature Heating Circuit ProblemProbe, tank or tank heater Troubleshooting Heating CircuitProblem Probable Cause Control Board Spitting or excessive steaming Temperature Probe ContWater supply Lime build upBrew cycle will not start Display flashing Brewing Circuit Problem Probable CauseBrewing Circuit Problem Probable Cause RemedyDripping from spray head Lime build up Water temperatureRequired Weak beverage SprayheadTroubleshooting Brewing Circuit Cause Things to Check DiagnosticsContents ServiceComponent Access Control Board ServiceDisconnect the 11-pin connector from the control panel Switch Panel Switch PanelDispense Valve Dispense ValveLimit Thermostat Limit ThermostatTank Heater Tank HeaterTank Heater Wiring Service Tank HeaterCheck for continuity across the refill valve coil terminals Refill ValveLocation Warmer Elements120V AC 2 Wire 120/208V AC 3 Wire 120/240V AC 3 Wire Schematic Wiring Diagram Cdbc 15, 20Schematic Wiring Diagram CDBCP/CDBCPF 15, 20 120/208V AC 3 Wire 120/240V AC 3 Wire 120V AC 2 Wire200V AC Wire Single Phase100V AC

CDBCP, CDBCFP, CDBCF, S/N CDBC020213 specifications

The Bunn CDBCFP, S/N CDBC020213, is part of the CDB family of coffee brewers, specifically designed to offer exceptional flavor and brewing efficiency for commercial settings. This advanced machine is a significant upgrade from traditional brewing systems, focusing on precision, consistency, and ease of use.

One of the main features of the Bunn CDBCFP is its digital control system, which allows operators to easily customize brew recipes and temperatures. This feature not only enhances the flavor profile of the brewed coffee but also ensures that each cup meets customer expectations. The machine is equipped with a patented infusion technology that allows for full saturation of coffee grounds, maximizing extraction and delivering a robust flavor.

The Bunn CDBCFP also boasts a large capacity, making it ideal for high-demand environments like cafes, restaurants, and offices. The unit can brew up to 3.8 gallons of coffee per hour, ensuring a steady supply even during peak times. The design includes a dual-funnel brewing system, which helps to distribute water evenly over the coffee grounds, resulting in a more consistent extraction.

In terms of its construction, the CDBCFP features a durable stainless-steel body that withstands the rigors of commercial use. This not only ensures longevity but also makes it easy to clean and maintain. The brewer is designed with a sleek aesthetic, fitting effortlessly into any modern kitchen or service area.

Another notable characteristic is the machine's energy efficiency. The Bunn CDBCFP is designed to operate with low energy consumption, helping businesses to reduce their overall operational costs. Additionally, the brewer's quick recovery time means that it can be ready to brew within minutes, further enhancing its efficiency.

The Bunn CDBCFP, S/N CDBC020213, is also compatible with a variety of coffee types, allowing businesses to diversify their offerings. Whether it’s gourmet blends, single-origin coffees, or sustainability-focused products, the CDBCFP can handle them all with ease.

In summary, the Bunn CDBCFP stands out in the commercial coffee brewing landscape due to its digital controls, large brewing capacity, durable construction, energy efficiency, and versatility. For establishments looking to deliver high-quality coffee with reliability, this brewer is a top choice.
Top Page Image Contents