Bunn S/N CDBC020213, CDBCF Electrical Requirements, Plumbing Requirements, Electrical Hook-Up

Page 4

ELECTRICAL REQUIREMENTS

CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up.

Model 15 has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz.

WHITE

NEUTRAL

120V.A.C.

L2 RED

WHITE

120V.A.C.

208 or 240V.A.C.

L1 BLACK

NEUTRAL

L1 BLACK

120V.A.C.

Model 20 requires 2-wire, grounded service rated

120 volts ac, 20 amp, single phase, 60 Hz. Proceed as follows:

Model 35 requires 3-wire, grounded service rated 120/208 or 120/240 volts ac, 20 amp, single phase, 60 Hz. Proceed as follows:

Electrical Hook-Up

CAUTION Ð Improper electrical installation will damage electronic components.

1.An electrician must provide electrical service as specified.

2.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

3.Remove the front panel beneath the sprayhead.

4.Feed the cord through the strain relief and connect it to the terminal block.

5.Connect the brewer to the power source and verify the voltage at the terminal block before proceeding. Replace the front panel.

6.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing has been hooked up, the brewer is ready for Initial Set-Up.

PLUMBING REQUIREMENTS

These brewers must be connected to a cold water system with operating pressure between 5 and 90 psi (34.5 and 620 kPa) from a 1Ú2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 1Ú4" flare. Bunn-O-Matic does not recommend the use of a reverse-osmosis or deionized water supply to this equipment.

NOTE - Bunn-O-Matic recommends 1Ú4" copper tubing for installations of less than 25 feet and 3Ú8" for more than 25 feet from the 1Ú2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the

Building Officials and Code Administrators International, Inc. (BOCA)

and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).

Plumbing Hook-Up

1.Flush the water line.

2.Securely attach it to the flare fitting at the rear of the brewer.

3.Turn on the water supply.

Page 4

35582 091503

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents DIS Vers ION BUNN-O-MATIC Commercial Product Warranty ContentsIntroduction User Notices Plumbing Requirements Electrical RequirementsElectrical Hook-Up ON/OFF Switch Brew SwitchReady Indicator Temperature IndicatorsInitial SET-UP Coffee BrewingPOUR-OVER Feature CleaningCDBC, Single CD Adjustments & Optional Settings Setting Brew TemperatureAdjustments & Optional Settings Water Sensing Threshold Adjustment ProcedurePulse Brew Setup Procedure Cdbc & Single CD Troubleshooting Before troubleshooting this brewer, check for the followingRefill Circuit Problem Probable Cause TroubleshootingRemedy Troubleshooting Refill Circuit Fill or refill does not shut OFF ON/OFF Switch onHeating Circuit Problem Water does not heat to proper temperatureProblem Probable Cause Troubleshooting Heating CircuitProbe, tank or tank heater Spitting or excessive steaming Temperature Probe Cont Control BoardWater supply Lime build upBrewing Circuit Problem Probable Cause Brew cycle will not start Display flashingProblem Probable Cause Remedy Brewing CircuitWater temperature Dripping from spray head Lime build upRequired Weak beverage SprayheadTroubleshooting Brewing Circuit Diagnostics Cause Things to CheckComponent Access ServiceContents Disconnect the 11-pin connector from the control panel ServiceControl Board Switch Panel Switch PanelDispense Valve Dispense ValveLimit Thermostat Limit ThermostatTank Heater Tank HeaterService Tank Heater Tank Heater WiringRefill Valve Check for continuity across the refill valve coil terminalsWarmer Elements LocationSchematic Wiring Diagram Cdbc 15, 20 120V AC 2 Wire 120/208V AC 3 Wire 120/240V AC 3 WireSchematic Wiring Diagram CDBCP/CDBCPF 15, 20 120V AC 2 Wire 120/208V AC 3 Wire 120/240V AC 3 WireWire Single Phase 200V AC100V AC

CDBCP, CDBCFP, CDBCF, S/N CDBC020213 specifications

The Bunn CDBCFP, S/N CDBC020213, is part of the CDB family of coffee brewers, specifically designed to offer exceptional flavor and brewing efficiency for commercial settings. This advanced machine is a significant upgrade from traditional brewing systems, focusing on precision, consistency, and ease of use.

One of the main features of the Bunn CDBCFP is its digital control system, which allows operators to easily customize brew recipes and temperatures. This feature not only enhances the flavor profile of the brewed coffee but also ensures that each cup meets customer expectations. The machine is equipped with a patented infusion technology that allows for full saturation of coffee grounds, maximizing extraction and delivering a robust flavor.

The Bunn CDBCFP also boasts a large capacity, making it ideal for high-demand environments like cafes, restaurants, and offices. The unit can brew up to 3.8 gallons of coffee per hour, ensuring a steady supply even during peak times. The design includes a dual-funnel brewing system, which helps to distribute water evenly over the coffee grounds, resulting in a more consistent extraction.

In terms of its construction, the CDBCFP features a durable stainless-steel body that withstands the rigors of commercial use. This not only ensures longevity but also makes it easy to clean and maintain. The brewer is designed with a sleek aesthetic, fitting effortlessly into any modern kitchen or service area.

Another notable characteristic is the machine's energy efficiency. The Bunn CDBCFP is designed to operate with low energy consumption, helping businesses to reduce their overall operational costs. Additionally, the brewer's quick recovery time means that it can be ready to brew within minutes, further enhancing its efficiency.

The Bunn CDBCFP, S/N CDBC020213, is also compatible with a variety of coffee types, allowing businesses to diversify their offerings. Whether it’s gourmet blends, single-origin coffees, or sustainability-focused products, the CDBCFP can handle them all with ease.

In summary, the Bunn CDBCFP stands out in the commercial coffee brewing landscape due to its digital controls, large brewing capacity, durable construction, energy efficiency, and versatility. For establishments looking to deliver high-quality coffee with reliability, this brewer is a top choice.
Top Page Image Contents