Bunn CDBCP, CDBCF Service, Control Board, Disconnect the 11-pin connector from the control panel

Page 23

SERVICE (cont.)

CONTROL BOARD

P1846

FIG. 2 CONTROL BOARD

Location:

The Control Board is located inside the top cover behind the front end cap.

Test Procedures:

The test procedures for the control board will vary depending upon the problems experienced by the brewer. Refer to the Troubleshooting guide beginning on page 9. The troubleshooting guide is divided into three sections, Refill Circuit, Heating Circuit, and Brew- ing Circuit.

Removal and Replacement:

1.Disconnect the black wire and blue wire from the relay on the control board.

2.Disconnect the 10-pin connector and the 4-pin connector from the main wiring harness.

3.Disconnect the 11-pin connector from the control panel.

4.Remove the four #6 screws and four nylon wash- ers and the two #4-40 screws securing the control board to the end cap assembly.

5.Install a new control board and secure with the four #6 screws and nylon washers and the two #4- 40 screws to the end cap assembly.

NOTE: The four nylon washers must be installed under the heads of the four #6 screws to prevent a possible shorting of the control board circuits.

6.Connect the 11-pin connector from the control panel.

7.Connect the 10-pin connector and the 4-pin con- nector from the main wiring harness.

8.Connect the blue wire and black wire to the relay on the control board.

9.Refer to CDBC , SINGLE CD Adjustments and Optional Settings to program the new control board.

Page 23

35582 041503

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents DIS Vers ION Introduction ContentsBUNN-O-MATIC Commercial Product Warranty User Notices Electrical Hook-Up Electrical RequirementsPlumbing Requirements Temperature Indicators ON/OFF SwitchBrew Switch Ready IndicatorCoffee Brewing Initial SET-UPCleaning POUR-OVER FeatureSetting Brew Temperature CDBC, Single CD Adjustments & Optional SettingsWater Sensing Threshold Adjustment Procedure Adjustments & Optional SettingsPulse Brew Setup Procedure Cdbc & Single CD Before troubleshooting this brewer, check for the following TroubleshootingRemedy TroubleshootingRefill Circuit Problem Probable Cause Fill or refill does not shut OFF ON/OFF Switch on Troubleshooting Refill CircuitWater does not heat to proper temperature Heating Circuit ProblemProbe, tank or tank heater Troubleshooting Heating CircuitProblem Probable Cause Lime build up Spitting or excessive steaming Temperature Probe ContControl Board Water supplyBrew cycle will not start Display flashing Brewing Circuit Problem Probable CauseBrewing Circuit Problem Probable Cause RemedyWeak beverage Sprayhead Water temperatureDripping from spray head Lime build up RequiredTroubleshooting Brewing Circuit Cause Things to Check DiagnosticsContents ServiceComponent Access Control Board ServiceDisconnect the 11-pin connector from the control panel Switch Panel Switch PanelDispense Valve Dispense ValveLimit Thermostat Limit ThermostatTank Heater Tank HeaterTank Heater Wiring Service Tank HeaterCheck for continuity across the refill valve coil terminals Refill ValveLocation Warmer Elements120V AC 2 Wire 120/208V AC 3 Wire 120/240V AC 3 Wire Schematic Wiring Diagram Cdbc 15, 20Schematic Wiring Diagram CDBCP/CDBCPF 15, 20 120/208V AC 3 Wire 120/240V AC 3 Wire 120V AC 2 Wire200V AC Wire Single Phase100V AC

CDBCP, CDBCFP, CDBCF, S/N CDBC020213 specifications

The Bunn CDBCFP, S/N CDBC020213, is part of the CDB family of coffee brewers, specifically designed to offer exceptional flavor and brewing efficiency for commercial settings. This advanced machine is a significant upgrade from traditional brewing systems, focusing on precision, consistency, and ease of use.

One of the main features of the Bunn CDBCFP is its digital control system, which allows operators to easily customize brew recipes and temperatures. This feature not only enhances the flavor profile of the brewed coffee but also ensures that each cup meets customer expectations. The machine is equipped with a patented infusion technology that allows for full saturation of coffee grounds, maximizing extraction and delivering a robust flavor.

The Bunn CDBCFP also boasts a large capacity, making it ideal for high-demand environments like cafes, restaurants, and offices. The unit can brew up to 3.8 gallons of coffee per hour, ensuring a steady supply even during peak times. The design includes a dual-funnel brewing system, which helps to distribute water evenly over the coffee grounds, resulting in a more consistent extraction.

In terms of its construction, the CDBCFP features a durable stainless-steel body that withstands the rigors of commercial use. This not only ensures longevity but also makes it easy to clean and maintain. The brewer is designed with a sleek aesthetic, fitting effortlessly into any modern kitchen or service area.

Another notable characteristic is the machine's energy efficiency. The Bunn CDBCFP is designed to operate with low energy consumption, helping businesses to reduce their overall operational costs. Additionally, the brewer's quick recovery time means that it can be ready to brew within minutes, further enhancing its efficiency.

The Bunn CDBCFP, S/N CDBC020213, is also compatible with a variety of coffee types, allowing businesses to diversify their offerings. Whether it’s gourmet blends, single-origin coffees, or sustainability-focused products, the CDBCFP can handle them all with ease.

In summary, the Bunn CDBCFP stands out in the commercial coffee brewing landscape due to its digital controls, large brewing capacity, durable construction, energy efficiency, and versatility. For establishments looking to deliver high-quality coffee with reliability, this brewer is a top choice.
Top Page Image Contents