Bunn H5X Service Dispense Valve PC Only, Location Dispense Valve is located behind control panel

Page 18

SERVICE (cont.)

Dispense Valve (PC Only)

Location:

The Dispense Valve is located behind control panel.

If voltage is not present as described, refer to Wir- ing Diagrams and check the dispenser wiring harness. Also check the control board for proper operation.

Bracket

Shroud

Dispense valve

Nut

Flare nut

FIG. 18a DISPENSE VALVE

Test Procedures:

1.Check the valve for coil action. Turn on the valve with the dispense button. Listen carefully in the vicinity of the dispense valve for a click as the coil pulls the plunger in.

If no sound is heard as described, proceed to #2. If the sound is heard as described, there may be a

blockage in the valve. Disconnect the dispenser from the power source. Remove the valve and inspect for blockage, and de-lime all related areas.

2.Connect voltmeter leads to the coil terminals. Turn on the valve with the dispense button. NOTE: Due to the internally rectified coil, the indication will be 120VAC all the time. Set the meter to DC volts. The indication should be 170VDC when activated. If the polarity of meter leads are reversed, reading will indicate -170VDC. (Double these readings for 240 volt coils)

If voltage is present as described, but no coil action is observed, valve is defective. Replace valve and test again to verify repair.

Removal and Replacement:

1.Disconnect the dispenser from the power source and allow to cool.

2.Drain enough water from the tank so the water level is below the outlet.

3.Remove the nut and flare nut from the valve.

4.Remove the top cover, shroud, and bracket.

5.Disconnect wires from the valve.

6.Using a back up wrench to hold fitting in place, Remove the valve.

7.Wrap threads of fitting with Teflon tape and install new valve.

8.Install bracket, nut, flare nut, wires and covers.

FIG. 18b

VALVE REMOVAL

REPAIR KIT

FIG. 18c

VALVE REPAIR KIT

18

42311 071310

 

Image 18
Contents H5E/DV PC Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Contents 19-23Problem Probable Cause Remedy FlashesProblem Probable Cause Lime build-up Water boils continuously Temperature controlNoises Water supply Ready indicator will not light Deposits. Delime as requiredComponent Access H5E/DV-PC/X Component Access H10XLiquid Level Control Flow Charts Electronic ControlsLocation Service Electronic Controls Liquid Level Control Test ProcedureService H5X Thermostat Replace the electronic control board Service Limit Thermostat Test ProcedureLocation Limit thermostat is located on the tank lid Service Safety Overflow Switch Safety Overflow WiringService Solenoid Valve Late Models If voltage was present as described, proceed to #5Service Solenoid Valve Early Models Service Tank Heater Location Tank heater is located in the tank lidCheck for continuity across the tank heater termi- nals Service Steam Sensor Thermistor Thermistor PositionService Dispense Valve PC Only Location Dispense Valve is located behind control panelSingle Phase 230V AC 2 Wire + GND Wire + GND Schematic Wiring Diagram H5E/H5X Wire + GND Single Phase
Related manuals
Manual 25 pages 51 Kb Manual 9 pages 10.17 Kb Manual 2 pages 44.15 Kb Manual 25 pages 6.43 Kb

DV, H5E, H5X specifications

The Bunn H5E and H5X coffee machines represent a leap forward in brewing technology, specifically tailored for commercial use. Both models focus on delivering high-quality coffee while maximizing efficiency, making them ideal choices for busy cafés and restaurants.

The Bunn H5E features a unique 5-liter dual tank system, which allows for faster brewing times and reduces wait periods for customers. This dual tank setup facilitates the simultaneous preparation of multiple coffee types, catering to a diverse clientele. The H5X, on the other hand, is equipped with advanced electronic controls that permit precise temperature adjustments to ensure that the ideal brewing conditions are maintained, enhancing flavor extraction.

One of the standout features of both models is the patented BrewOptimized Technology. This technology helps maintain optimal water temperature and consistent flow rates throughout the brewing process, ensuring that each cup of coffee meets the high standards expected in commercial settings. Additionally, the units utilize a patented stainless steel brew basket that enhances durability and simplifies cleaning, making maintenance less of a chore for busy staff.

Another significant characteristic of the H5E and H5X is their programmable settings, which allow operators to customize brewing parameters according to their specific preferences or customer needs. This flexibility means that establishments can experiment with various coffee profiles, ensuring that they serve only the best products to their patrons.

Safety is also a priority in the design of these machines. The H5E and H5X come equipped with built-in safety features such as automatic shut-off and thermal overload protection, which help to prevent accidents and enhance longevity. Moreover, their compact design allows for easy installation in a variety of settings, whether it's a small coffee stand or a large restaurant operation.

Both the Bunn H5E and H5X models are energy-efficient, with features that minimize power consumption without compromising performance. This focus on sustainability not only helps reduce overhead costs but also appeals to environmentally conscious consumers.

In summary, the Bunn H5E and H5X coffee machines are engineered for high performance, reliability, and versatility. With features designed to provide quick, quality coffee while ensuring ease of operation and maintenance, these machines are ideal for any establishment that takes its coffee seriously. Whether you’re brewing for a crowd or crafting specialty drinks, the H5E and H5X stand ready to deliver excellent results every time.