Bunn POWDER AUTO FILL service manual User Notices

Page 3

10.Slowly feed the door support arms through the slots located on the front of the Powder Auto-Fill.

11.Continue to slowly feed the door support arms through the slots until the magnet strikes on the back of the door engage the magnets on the Powder Auto-Fill.

12.Locate the #8-32 x .375" truss head screws and brass spacers set aside earlier.

13.Place one brass spacer on each screw.

14.Insert one screw/spacer assembly through the door hinge, locating the spacer inside the hinge bushing and threading the screw into the hinge mount on the Powder Auto-Fill cover. Repeat for other side.

15.Install PAF level probe (BOM #29728.1000) by sliding it into the notched area at the top rear of the CDS hopper. The probe should be firmly seated in the notch and touching the contact pin protruding from the front of the CDS cooling drum mount.

NOTE: At this point, it is important that the CDS machine is fully assembled according to the instructions outlined in the CDS Operating and Service Manual.

16.Place the assembled Powder Auto-Fill on top of a hopper of a fully assembled CDS machine, taking care to align the Powder Auto-Fill guide rails over the rollers on the CDS.

17.Connect the Powder Auto-Fill power cord to the outlet located on the CDS auger motor cover.

18.Attach a flexible water line to the .25" flare fitting on the back panel of the Powder Auto-Fill.

NOTE: A water strainer assembly (BUNN-O-MATIC #23820.1000) should be installed in line prior to the flexible water line.

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

00656.0000 00986.0000

3

29793 011500

 

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Bunn Powder Auto Fill Warranty Initial SET-UPIntroduction User Notices Operating Instructions Adjustments Cleaning Recommended Daily Cleaning and Maintenance TipsRinse and dry each item thoroughly before reas- sembling Door not closed Fault ListNormal operation Powder Auto-Fill ready to DispenseProblem Probable Cause TroubleshootingProblem RemedyCDS product tastes watery or sugary Problem Probable Cause Remedy Product overflows CDS hopper Control Board and Probe Procedures. SeeImproper adjustment of product Install a regulator if necessary toComponent Access ServiceSpacer Dust Seal Hopper Base Auger Drive ComponentsHopper Lid Retainer ClipAuger Drive Motor Diagrams and check wiring harnessMixing Chamber Frother and MIXING/WHIPPER ChamberVolts ac for 120 volt models Volts ac for 230 volt CE models Whipper MotorWhipper Motor Install dispense tip into the bottom of the whipper chamberIf voltage is present as described, proceed to #9 If voltage is present as described, proceed to #5Test Procedure Low Product Detect Remove the control board Instal the new control board using the four #6-32 keps nutsTEST/SERVICE Switch Disconnect the wires from the switch terminalsLocation Main Power ON/OFF Switch Main Power ON/OFF SwitchRefer to when reconnecting the wires Lamp Cord AssemblyLamp Cord Connector Disconnect the lamp cord from the lamp cord connectorRemove new nut and washer from new lamp cord connector Close the dispenser door Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchPressure Regulator and Needle Valve AdjustmentsDispense Solenoid Valve Location Dispense Solenoid ValveBLK RED Wiring Diagrams Schematic Wiring Diagram PAFWiring Diagrams Schematic Wiring Diagram Pafa
Top Page Image Contents