Bunn POWDER AUTO FILL service manual Test Procedure Low Product Detect

Page 19

SERVICE (cont.)

CONTROL BOARD and LEVEL PROBE (cont.)

Test Procedure:

Low Product Detect

1.Disconnect the dispenser from the power source.

2.Disconnect the twelve pin connector (J1) from the control board.

3.Check the voltage across pins 2 & 3 of the twelve pin connector on the wiring harness with a voltmeter. Connect the dispenser to the power source and select the "ON" position of the main power switch. The indication must be 24 volts ac.

4.Select the "OFF" position of the main power switch and disconnect the dispenser from the power source.

If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to the wiring diagram and check the dispenser wiring harness.

5.Reconnect the twelve pin connector to the control board (J1).

6.Disconnect the four pin connector (J6) from the control board.

7.Check the voltage across pins 1 (positive) & 3 (negative) of the four pin connector on the control board with a voltmeter. Connect the dispenser to the power source and select the "ON" position of the main power switch. The indication must be +5 volts dc.

8.Select the "OFF" position of the main power switch and disconnect the dispenser from the power source.

If voltage is present as described, proceed to #9.

If voltage is not present as described, replace the control board.

9.Reconnect the four pin connector to the control board (J6).

10.Check the voltage across pins 1 (positive) & 3 (negative) of the four pin connector on the control board with a voltmeter. Place a full hopper in the dispenser, connect the dispenser to the power source, select the "ON" position on the main power switch, and close the dispenser door. The indica- tion must be +5 volts dc.

11.Disconnect the dispenser from the power source, remove the jumper wire, and select the "OFF" posi- tion on the main power switch.

If voltage is present as described, proceed to #12.

If voltage is not present as described, replace the photo transistor.

12.Check the voltage across pins 1 (positive) & 3 (negative) of the four pin connector on the control board with a voltmeter. Remove the hopper from the dispenser, connect the dispenser to the power source and select the "ON" position of the main power switch. Shine a flashlight on the photo transistor (left side panel). The indication must be less than 1 volt dc.

13.Disconnect the dispenser from the power source and select the "OFF" position on the main power switch.

If voltage is present as described, proceed to #14.

If voltage is not present as described, replace the photo transistor.

14.Disconnect the two pin connector (J2) from the control board.

15.Check the voltage across pins 1 (positive) & 2 (negative) of the two pin connector on the control board with a voltmeter. Connect the dispenser to the power source and select the "ON" position of the main power switch. The indication must be +1.5 volts dc.

16.Select the "OFF" position of the main power switch and disconnect the dispenser from the power source.

If voltage is present as described, proceed to #17.

If voltage is not present as described, replace the control board.

17.Check the photo LED forward and reverse bias using a diode tester. The photo LED must be forward biased with positive applied to pin 1 of the two pin connector and negative applied to pin 2 of the two pin connector. The photo LED must be reverse biased with negative applied to pin 1 of the two pin connector and positive applied to pin 2 of the two in connector.

If the photo LED biasing checks as described, the low level detect circuitry is operating properly.

If the photo LED biasing does not check as described, replace the photo LED.

NOTE: The photo LED lights in the infrared spectrum and is not visible to the human eye.

19

29793 061599

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Bunn Powder Auto Fill Initial SET-UP WarrantyIntroduction User Notices Operating Instructions Adjustments Recommended Daily Cleaning and Maintenance Tips CleaningRinse and dry each item thoroughly before reas- sembling Door not closed Fault ListNormal operation Powder Auto-Fill ready to DispenseProblem Probable Cause TroubleshootingRemedy ProblemCDS product tastes watery or sugary Problem Probable Cause Remedy Product overflows CDS hopper Control Board and Probe Procedures. SeeImproper adjustment of product Install a regulator if necessary toComponent Access ServiceSpacer Dust Seal Hopper Base Auger Drive ComponentsHopper Lid Retainer ClipAuger Drive Motor Diagrams and check wiring harnessMixing Chamber Frother and MIXING/WHIPPER ChamberVolts ac for 120 volt models Volts ac for 230 volt CE models Whipper MotorWhipper Motor Install dispense tip into the bottom of the whipper chamberIf voltage is present as described, proceed to #9 If voltage is present as described, proceed to #5Test Procedure Low Product Detect Remove the control board Instal the new control board using the four #6-32 keps nutsDisconnect the wires from the switch terminals TEST/SERVICE SwitchLocation Main Power ON/OFF Switch Main Power ON/OFF SwitchRefer to when reconnecting the wires Lamp Cord AssemblyDisconnect the lamp cord from the lamp cord connector Lamp Cord ConnectorRemove new nut and washer from new lamp cord connector Close the dispenser door Lamp HOLDER/SOCKET AssemblyTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchPressure Regulator and Needle Valve AdjustmentsDispense Solenoid Valve Location Dispense Solenoid ValveBLK RED Wiring Diagrams Schematic Wiring Diagram PAFWiring Diagrams Schematic Wiring Diagram Pafa

POWDER AUTO FILL specifications

The Bunn Powder Auto Fill is a cutting-edge coffee brewing system designed to enhance efficiency and precision in commercial environments. This innovative machine simplifies the brewing process by incorporating automated features that ensure consistent quality and optimal performance.

One of the standout features of the Bunn Powder Auto Fill is its ability to automatically dispense powdered beverage mixes. This is made possible through advanced technology that streamlines the process, reducing the need for manual input. With the push of a button, operators can quickly prepare a variety of specialty beverages, including cappuccinos, lattes, and flavored coffee drinks. This not only saves time but also minimizes the likelihood of human error in measurements, ensuring each cup is consistently brewed to perfection.

The Bunn Powder Auto Fill is designed with versatility in mind. It accommodates a wide range of powdered ingredients, allowing businesses to offer an extensive menu without investing in multiple machines. This adaptability makes it an ideal solution for coffee shops, convenience stores, and other establishments where customer preferences may vary.

Moreover, the machine features a robust heating system that provides rapid brewing capabilities. This ensures that beverages are served at the optimal temperature, enhancing the overall customer experience. The integrated hot water faucet allows for quick access to hot water, making it easy to prepare additional drinks or even food items like soups and oatmeal.

Durability is another key characteristic of the Bunn Powder Auto Fill. Built with high-quality materials to withstand the rigors of daily use, this machine is designed to deliver reliable performance over time. Its compact and sleek design allows for easy placement in any setting, taking up minimal counter space while blending seamlessly with existing décor.

Additionally, the Bunn Powder Auto Fill incorporates user-friendly controls and displays. This intuitive interface allows staff to quickly familiarize themselves with the machine's operation, which is crucial in high-demand environments. The system also features programmable settings, enabling users to customize brew strengths and portion sizes according to customer preferences.

In conclusion, the Bunn Powder Auto Fill is a game-changer for businesses looking to elevate their beverage offerings. With its automation, versatility, reliability, and user-centric design, this machine not only boosts efficiency but also enhances the quality of every cup served. Whether in a bustling café or a busy convenience store, the Bunn Powder Auto Fill stands out as a smart investment for any beverage-focused establishment.
Top Page Image Contents