Bunn ULTRA-2 manual Service Relay or Contactor on Early Models

Page 43
FIG. 32 RELAY

SERVICE (cont.)

RELAY (or CONTACTOR on Early Models)

ULTRA-2 shown

Location:

The relay (or contactor) is located inside the dis- penser chassis on the lower outside of the component

If continuity is present as described, disconnect the dispenser from power source and reconnect wires to terminals #6 and #8, the relay is working.

If continuity is not present as described, do the same continuity test across terminals #2 and #4. If continu- ity is present between terminals #2 and #4, reconnecr wires to terminals #2 and #4 instead of #6 and #8.

If continuity is not present as described, replace the relay.

Removal and Replacement:

1.Disconnect the wires from the relay.

2.Remove the two #8-32 locking screws securing the relay to the chassis. Remove and discard relay.

3.Install the new relay on the chassis using two #8-32 locking screws.

4.Refer to Fig. 33 and 34 to reconnect the wires.

Early Model ULTRA-2

bracket.

Test Procedures:

1.

Disconnect the dispenser from the power source.

2.

Remove the right side panel.

3.

Connect the dispenser to the power source.

4.

Turn on power (I/O) switch. Verify UPPER case

 

“ICE” or “CHILL” mode.

5.

With a voltmeter, check the voltage across the white

Terminal #4

Terminal #2

Terminal #6

BLK from Main

Harness/Power Cord

Terminal #8

WHI/ORN from

Compressor Harness

Terminal #0

WHI from Main Harness

Terminal #1

ORN from

Control Board

wire and the orange wire.

The indication must be:

a) 120 volts ac for 120 volt models.

b) 230 volts ac for 230 volt models.

6. Disconnect the dispenser from the power source.

If voltage is present as described, proceed to #7.

If voltage is not present as described, refer to the Wir- ing Diagram and check the dispenser wiring harness. If harness has continuity, replace Control Board.

7.Disconnect the black wire and the WHI/ORN wires from relay terminals #6 and #8.

8.Connect the dispenser to the power source.

9.Turn on power (I/O) switch. Verify UPPER case “ICE” or “CHILL” and check for continuity across terminals on relay.

 

P1333

FIG. 33 CONTACTOR TERMINALS

 

 

Late Model ULTRA-2 & ULTRA-1

Terminal #0

Terminal #1

WHI from

ORN from

Main Harness

Main Harness

 

Terminal #8

 

BLK from

 

Main Harness

Terminal #2

Terminal #6

Terminal #4

WHI/ORN from

Main Harness

 

FIG. 34 RELAY TERMINALS

43

41084 102709

 

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Phone 217 529-6601 FAX 217 ULTRA-1 ULTRA-2BUNN-O-MATIC Commercial Product Warranty User Notices ContentsIntroduction Temp & Torque Screen Operating Controls ULTRA-1 Operating Controls ULTRA-2 Switch upper left corner of the control padSurface Other and disconnect from Be taken when handling HopperFrom the rear of the drum Under spring tension. Spread One side of the handle first, thenAssemble the drip tray Drums and press the sealsFirmly into place as shown Auger noseMaterials required Sanitizing ProcedureNormal Operation Preventive MaintenanceDescription Required Regular MaintenanceKit Contents InstructionsRequired Regular Maintenance No Power TroubleshootingBoard Done Adjust Clean Troubleshooting Chills but Won’t freezeSet into DAY mode Set into ICE mode Is display showingTroubleshooting No cooling At all Adjust thickness Screen higher Troubleshooting Freezes, but not Thick enoughBrix ratio Too much Auger won’t turn Troubleshooting NoiseAuger jumping Check fan Drum alignment Check auger shaft bushingsTorque Sensor Shorted Torque Sensor Open TroubleshootingTorque Sensor Error Torque Sensor ErrorTemperature Sensor Shorted Troubleshooting Temperature Sensor ErrorTemperature Sensor Open Monthly reminder Troubleshooting Clean Filter MessagesFilter Needs Cleaning Freezing is DisabledComponent Access Panels ServiceAuger Motors SERVICEcontMotor Coil Resistance Auger Motor Capacitors Auger Motor CapacitorAuger Shaft Assembly Auger Shaft AssemblyRemove and clean condenser air filter, Fig Service Auger Shaft ASSEMBLYcontLocation Test ProceduresRemove the wires from the circuit breaker Circuit Breaker120V Compressors 230V Compressors Compressor Start Relay Terminals Service Compressor Assy Compressor Embraco ULTRA-2Model T-2155 Service Compressor Embraco ULTRA-2Model T-2168 Secure compressor to the dispenser chassis using four Capacitor Ratings Compressor SpecificationCSR Motor Wiring Diagram Compressor ModelCompressor Wiring Diagram Important SafeguardsDisconnect all electrical power to the Bunn ULTRA-2 HP Testing Compressor Windings/Insulation with a Meg- gerRun Capacitior External Thermal ProtectorPotential Start Relay Mounting Position Start CapacitorCompressor Thermal Compressor Appliances ULTRA-1Relay Terminals Service Service Compressor Danfoss ULTRA-1B Compressor Capacitor Terminals Service Relay or Contactor on Early Models TIC board Control BoardCooling Drum Shipping Support Cooling Drum AlignmentUse cable ties to secure wires away from fan blades Front of the condenser Test ProceduresFAN ULTRA-2 FAN FAN ULTRA-1Alternate Test HOT GAS Temperature SensorLamp Cord Assy Lamp Cord WiresLamp Cord Connector Lamp Cord ConnectorLamp HOLDER/SOCKET Assembly Lamp HOLDER/SOCKET AssemblyDisconnect the black and red leads from the LEDs Service LED LampsULTRA-2 ULTRA-1 Lamp RelayRibbon Cable Membrane Switch ULTRA-2Refer to and connect the ribbon cable to the Control Board Membrane Switch ULTRA-1WHI from Main Harness SolenoidsTemperature Sensor Temperature SensorDo not Turn on Augers Torque Sensor Circuit BoardLoad TransformerCoolant Schematic ULTRA-1 Coolant Schematic ULTRA-2 TH1 & MOV4 Controls Auger ULTRA-1 TriacsTH6 & MOV6 Controls Right Auger Liquid AUTO-FILL Board ULTRA-2 TriacsInput and Output Chart ULTRA-1 Schematic Wiring Diagram ULTRA-1 Input and Output Chart ULTRA-2 Schematic Wiring Diagram ULTRA-2 AF 41084
Related manuals
Manual 23 pages 57.86 Kb Manual 19 pages 61.15 Kb

ULTRA-2 specifications

The Bunn ULTRA-2 is an exceptional frozen beverage dispenser that caters to both commercial and home use, making it a popular choice in various establishments such as cafes, restaurants, and convenience stores. Renowned for its reliability and efficiency, the ULTRA-2 serves a wide range of frozen beverages, including slushes, smoothies, and frozen cocktails, providing an irresistible treat for customers.

One of the standout features of the Bunn ULTRA-2 is its high-capacity design. With a dual hopper system, this machine allows operators to serve two different flavors simultaneously. Each hopper can hold up to 3.2 gallons of product, allowing for continuous service without the need for frequent refills. This is particularly advantageous during peak hours when demand is high.

The ULTRA-2 is equipped with Bunn's advanced refrigeration technology, which ensures rapid freezing and consistent product quality. The machine uses a patented freezing mechanism that maintains optimal product texture and temperature, resulting in a smooth, uniform consistency that keeps customers coming back for more. Additionally, the ULTRA-2's adjustable temperature control allows operators to customize the consistency of the beverages to their liking.

User-friendliness is another hallmark of the Bunn ULTRA-2. The machine features intuitive controls that simplify operation, making it easy for staff to learn and use efficiently. A built-in safety feature prevents the machine from operating when the hoppers are too low, minimizing waste and ensuring product quality.

Durability and ease of maintenance are also prominent characteristics of the ULTRA-2. Constructed from high-quality stainless steel, the machine offers enhanced longevity and is resistant to rust and corrosion. The removable hoppers and door assemblies facilitate quick cleaning and maintenance, allowing businesses to keep the machine in top working condition with minimal effort.

In summary, the Bunn ULTRA-2 stands out in the crowded market of frozen beverage dispensers through its dual hopper functionality, advanced refrigeration technology, user-friendly design, and robust construction. Whether for a busy café or a family gathering, the ULTRA-2 provides a reliable solution for delivering delicious frozen beverages that satisfy a variety of tastes and preferences.
Top Page Image Contents