Bunn ULTRA-2 manual Lamp Cord Connector

Page 50

SERVICE (cont.)

LAMP CORD CONNECTOR

ULTRA-2 shown

FIG. 47 LAMP CORD CONNECTOR Location:

The lamp cord connectors are located inside the center top of the auger motor covers.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Disconnect the plug on the dispenser main harness from the connector from the lamp cord connec- tor.

3.Connect the dispenser to the power source. Turnon power (I/O) switch. The indication must be approxi- mately 12.6 volts dc.

4.Disconnect the dispenser from the power source. If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to the Wiring Diagram and check the dispenser main wiring harness.

NOTE: Lamp cord assembly (Fig. 47) and lamps, must be tested and determined to be functioning properly before proceeding to step 5.

5.Check for continuity across the black wire pin and red wire pin of the lamp cord connector (Fig. 48). Continuity must be present when the lamp cord assembly is connected and must not be present when lamp cord assembly is disconnected from lamp cord connector.

If continuity is not present when lamp cord assembly is connected or continuity is present when lamp cord assembly is not connected, replace the lamp cord connector.

Removal and Replacement:

1.Disconnect the lamp cord assembly from the lamp cord connector.

2.Remove the two #8-32 locking screws securing the auger motor cover the auger motor bracket/cooling drum bracket. Move cover back far enough to gain access to the lamp cord connector.

3.Disconnect the lamp cord connector wires from the dispenser main wiring harness.

4.Remove nut and washer securing the lamp cord connector to the auger motor cover and discard nut, washer and lamp cord connector.

5.Remove new nut and washer from new lamp cord connector.

6.Push new lamp cord connector through the hole in the auger motor cover and secure with the new nut and washer.

7.Reconnect the wires on the cord connector to the dispenser main wiring harness.

8.Position auger motor cover on auger motor bracket/ cooling drum bracket and secure with two #8-32 locking screws.

9.Refer to Fig. 48 when reconnecting wires.

BLK to Main Wiring Harness

RED to Main Wiring Harness

FIG.48 LAMP CORD CONNECTOR

P1323

 

50

41084 102709

 

Image 50
Contents ULTRA-1 ULTRA-2 Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Contents User NoticesIntroduction Temp & Torque Screen Operating Controls ULTRA-1 Switch upper left corner of the control pad Operating Controls ULTRA-2One side of the handle first, then Other and disconnect from Be taken when handling HopperFrom the rear of the drum Under spring tension. Spread SurfaceAuger nose Drums and press the sealsFirmly into place as shown Assemble the drip traySanitizing Procedure Materials requiredPreventive Maintenance Normal OperationInstructions Required Regular MaintenanceKit Contents DescriptionRequired Regular Maintenance Board TroubleshootingNo Power Set into ICE mode Is display showing Troubleshooting Chills but Won’t freezeSet into DAY mode Done Adjust CleanTroubleshooting No cooling At all Brix ratio Too much Troubleshooting Freezes, but not Thick enoughAdjust thickness Screen higher Drum alignment Check auger shaft bushings Troubleshooting NoiseAuger jumping Check fan Auger won’t turnTorque Sensor Error TroubleshootingTorque Sensor Error Torque Sensor Shorted Torque Sensor OpenTemperature Sensor Open Troubleshooting Temperature Sensor ErrorTemperature Sensor Shorted Freezing is Disabled Troubleshooting Clean Filter MessagesFilter Needs Cleaning Monthly reminderService Component Access PanelsMotor Coil Resistance SERVICEcontAuger Motors Auger Motor Capacitor Auger Motor CapacitorsAuger Shaft Assembly Auger Shaft AssemblyService Auger Shaft ASSEMBLYcont Remove and clean condenser air filter, FigCircuit Breaker Test ProceduresRemove the wires from the circuit breaker Location120V Compressors 230V Compressors Compressor Start Relay Terminals Service Compressor Embraco ULTRA-2 Compressor AssyModel T-2168 Service Compressor Embraco ULTRA-2Model T-2155 Secure compressor to the dispenser chassis using four Compressor Model Compressor SpecificationCSR Motor Wiring Diagram Capacitor RatingsImportant Safeguards Compressor Wiring DiagramTesting Compressor Windings/Insulation with a Meg- ger Disconnect all electrical power to the Bunn ULTRA-2 HPStart Capacitor External Thermal ProtectorPotential Start Relay Mounting Position Run CapacitiorCompressor Appliances ULTRA-1 Compressor ThermalRelay Terminals Service Service Compressor Danfoss ULTRA-1B Compressor Capacitor Terminals Service Relay or Contactor on Early Models Control Board TIC boardCooling Drum Alignment Cooling Drum Shipping SupportFAN ULTRA-2 Front of the condenser Test ProceduresUse cable ties to secure wires away from fan blades FAN ULTRA-1 FANHOT GAS Temperature Sensor Alternate TestLamp Cord Wires Lamp Cord AssyLamp Cord Connector Lamp Cord ConnectorLamp HOLDER/SOCKET Assembly Lamp HOLDER/SOCKET AssemblyService LED Lamps Disconnect the black and red leads from the LEDsLamp Relay ULTRA-2 ULTRA-1Membrane Switch ULTRA-2 Ribbon CableMembrane Switch ULTRA-1 Refer to and connect the ribbon cable to the Control BoardSolenoids WHI from Main HarnessTemperature Sensor Temperature SensorTorque Sensor Circuit Board Do not Turn on AugersTransformer LoadCoolant Schematic ULTRA-1 Coolant Schematic ULTRA-2 ULTRA-1 Triacs TH1 & MOV4 Controls AugerLiquid AUTO-FILL Board ULTRA-2 Triacs TH6 & MOV6 Controls Right AugerInput and Output Chart ULTRA-1 Schematic Wiring Diagram ULTRA-1 Input and Output Chart ULTRA-2 Schematic Wiring Diagram ULTRA-2 AF 41084
Related manuals
Manual 23 pages 57.86 Kb Manual 19 pages 61.15 Kb

ULTRA-2 specifications

The Bunn ULTRA-2 is an exceptional frozen beverage dispenser that caters to both commercial and home use, making it a popular choice in various establishments such as cafes, restaurants, and convenience stores. Renowned for its reliability and efficiency, the ULTRA-2 serves a wide range of frozen beverages, including slushes, smoothies, and frozen cocktails, providing an irresistible treat for customers.

One of the standout features of the Bunn ULTRA-2 is its high-capacity design. With a dual hopper system, this machine allows operators to serve two different flavors simultaneously. Each hopper can hold up to 3.2 gallons of product, allowing for continuous service without the need for frequent refills. This is particularly advantageous during peak hours when demand is high.

The ULTRA-2 is equipped with Bunn's advanced refrigeration technology, which ensures rapid freezing and consistent product quality. The machine uses a patented freezing mechanism that maintains optimal product texture and temperature, resulting in a smooth, uniform consistency that keeps customers coming back for more. Additionally, the ULTRA-2's adjustable temperature control allows operators to customize the consistency of the beverages to their liking.

User-friendliness is another hallmark of the Bunn ULTRA-2. The machine features intuitive controls that simplify operation, making it easy for staff to learn and use efficiently. A built-in safety feature prevents the machine from operating when the hoppers are too low, minimizing waste and ensuring product quality.

Durability and ease of maintenance are also prominent characteristics of the ULTRA-2. Constructed from high-quality stainless steel, the machine offers enhanced longevity and is resistant to rust and corrosion. The removable hoppers and door assemblies facilitate quick cleaning and maintenance, allowing businesses to keep the machine in top working condition with minimal effort.

In summary, the Bunn ULTRA-2 stands out in the crowded market of frozen beverage dispensers through its dual hopper functionality, advanced refrigeration technology, user-friendly design, and robust construction. Whether for a busy café or a family gathering, the ULTRA-2 provides a reliable solution for delivering delicious frozen beverages that satisfy a variety of tastes and preferences.