Bunn 37614 041410 manual Plumbing Requirements, Plumbing HOOK-UP, Initial Setup

Page 5

PLUMBING REQUIREMENTS

This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1⁄2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 3⁄8" flare.

NOTE: Bunn-O-Matic recommends 1⁄4" copper tubing for installations of less than 25 feet and 3⁄8" for more than 25 feet from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.

PLUMBING HOOK-UP

1.Flush the water supply line and securely attach it to the flare fitting or adapter located on rear of brewer.

2.Turn on the water supply.

INITIAL SETUP

CAUTION: The brewer must be disconnected from the power source throughout the initial setup, except when specified in the instructions.

1.Insert an empty funnel into the funnel rails of one of the brew stations.

2.Place an empty server under the funnel.

3.Connect the brewer to the power source. Main ON/OFF Switch (located in bottom cover behind right front leg on some brewers) must be in the ON position. Water will begin flowing into the tank and stop when the tank is filled to its capacity. Display will show PLEASE WAIT...TANK FILLING until tank is filled with water.

4.Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will show READY TO BREW...WATER TEMP: XXX˚ when tank is at operating temperature.

NOTE: Brew water temperature is factory set at 200° F (93.3° C). Areas of high altitude will require lowering this temperature to prevent boiling. Refer to chart in "SET TEMP" section when readjusting the brew temperature.

5.Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank refilling.

6.Water volumes have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of this manual should the volume need to be increased or decreased.

7.The brewer is now ready for use in accordance with the coffee brewing instructions.

Page 5

37614 042210

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Phone 217 529-6601 FAX 217 Dual / GPR-DBCIntroduction BUNN-O-MATIC Commercial Product Warranty00986.0000 User Notices37881.0000 03408.0004 03409.0004 12364.0000 00656.0001120/208 & 120/240 volt ac models Electrical RequirementsElectrical HOOK-UP Plumbing HOOK-UP Initial SetupPlumbing Requirements Operating Controls Main ON/OFF SwitchCoffee Brewing Cleaning

37614 041410 specifications

The Bunn 37614 041410 is a remarkable commercial coffee brewer, designed for high-volume environments such as restaurants, cafes, and offices. Known for its reliability and efficiency, this model stands out in the busy coffee service industry.

One of the main features of the Bunn 37614 041410 is its ability to brew large quantities of coffee quickly. This machine offers a brewing capacity of up to 3.8 gallons per hour, which is essential for establishments that serve a high number of customers within a short period. The brewer is capable of producing full and half batches, allowing for flexible operations depending on the demand throughout the day.

The Bunn 37614 041410 is equipped with advanced brewing technology that ensures optimal extraction of coffee flavors. Its unique spray head design evenly distributes water over the coffee grounds, facilitating optimal saturation and extraction process. This means that every cup served is full of rich, flavorful coffee, enhancing customer satisfaction.

Another key characteristic of this brewer is its user-friendly interface. The machine features simple controls that allow staff to start the brewing process with minimal training. The clear instructions and straightforward design streamline operations, making it easy for busy baristas to keep up with demand.

In addition to its brewing capabilities, the Bunn 37614 041410 comes with a built-in stainless steel water tank that maintains the ideal brewing temperature. This ensures that coffee is brewed at the right temperature for optimal flavor extraction, providing consistency across every batch.

Moreover, this model is constructed with durability in mind, featuring a robust stainless steel body that withstands the rigors of daily use. Its sleek design also makes it an appealing addition to any coffee service station.

Maintenance is made easy with the Bunn 37614 041410, as it allows for easy access to its internal components for cleaning and servicing. The machine's design minimizes the risk of clogs and malfunctions, ensuring that it remains in optimal working condition for years to come.

In summary, the Bunn 37614 041410 is a powerful coffee brewer that combines efficiency, durability, and excellent brewing technology. Its ability to produce large volumes of high-quality coffee quickly makes it an invaluable tool for any coffee-forward business.
Top Page Image Contents