Faucet Installation, Drill bits may be needed

Faucet Installation

Be sure there is room underneath the sink to make the needed connections. Select one of the following places to install the faucet:

—IN an existing sink spray attachment or soap dispenser hole.

—IN a hole to be drilled in the sink top.

—IN a hole to be drilled in the countertop, next to the sink.

NOTE: Looking at Fig. 3B, be sure the faucet base will fit flat against the surface at the selected location so the gasket will seal.

		If drilling is needed, make a 1″–1-1⁄4″ dia.
	1	If drilling is needed, make a 1″–1-1⁄4″ dia.
	1	hole. Be sure to use the proper procedure for
		hole. Be sure to use the proper procedure for
		drilling porcelain or stainless steel. Special
		drill bits may be needed.
		Place small gasket, base and large gasket (in
	2	Place small gasket, base and large gasket (in
	2	that order) on to the faucet stem. Next, place
		that order) on to the faucet stem. Next, place

lock washer and hex nut onto faucet stud.

Fig. 3A.

Insert washer into tubing adapter. Securely tighten to faucet stud.

Feed the length of 3⁄8″ OD tube from the bottom, up through the mounting hole. Connect to the tubing adapter as shown in Fig. 3B, tightening the compression nut securely.

Remove the short shipping tube and insert the spout into the faucet body. Rotate spout into place.

Lower the faucet assembly into place. Place the mounting bracket above the lock washer. While holding the mounting bracket in place, securely tighten the hex nut.

Fig. 3B.

Safety Instructions Operating Instructions Installation

Spout

Lever

Faucet

Faucet stud

ASSEMBLED

Small gasket

Base

Large gasket

Sink

Mounting bracket

Lock washer

Hex nut

Plastic washer

Tubing adaptor

Compression nut

3/8″ tubing, (run to Filter II outlet)

Instructions Troubleshooting Tips

Customer Service

GXUT03B, GNUT03B specifications

The GE GNUT03B and GXUT03B are advanced electronic units designed to enhance operational efficiency across various industrial applications. These models are part of General Electric's extensive portfolio, known for their reliability and innovative technology.

One of the standout features of the GNUT03B and GXUT03B is their robust communication capabilities. Both units support multiple protocols, which ensures seamless integration into existing systems. This interoperability allows for easy adaptability in complex environments including manufacturing plants, energy sectors, and smart grid systems. The units can communicate with different devices, controllers, and software applications, facilitating real-time data exchange and monitoring.

In terms of processing power, the GNUT03B and GXUT03B are equipped with high-performance processors that enable fast data processing and analysis. This capability is crucial for industries where timely decision-making impacts productivity and safety. The user-friendly interface of these units provides operators with intuitive access to their features, allowing for easy setup and navigation.

Another significant characteristic is the units' built-in redundancy features. These ensure continuous operation, minimizing downtime that can be costly in industrial settings. The GNUT03B and GXUT03B also include fail-safe mechanisms designed to protect critical operations, making them suitable for mission-critical applications.

Energy efficiency is another important aspect of these models. They are designed not only to provide high performance but also to reduce overall energy consumption. This not only leads to cost savings but also promotes sustainability, aligning with the growing emphasis on environmentally friendly practices in industry.

The GNUT03B and GXUT03B boast extensive data storage capabilities, enabling them to manage large volumes of information. This is particularly beneficial for applications requiring historical data analysis, predictive maintenance, and performance optimization. Their advanced analytics capabilities assist organizations in making data-driven decisions to enhance operational efficiency and reduce operational risks.

Finally, the durability and rugged design of these units make them suitable for harsh environments. They have been engineered to withstand extreme temperatures, vibration, and dust, which ensures a long operational life and minimizes the need for frequent replacements or repairs.

Overall, the GE GNUT03B and GXUT03B represent a fusion of cutting-edge technology and practical functionality, making them indispensable tools for modern industrial operations. With their impressive features and characteristics, they are well-equipped to meet the demands of an ever-evolving industrial landscape.