InSinkErator Complete Guide to Mounting Assembly for Smooth Garbage Disposal Installation

Page 7

InSinkErator Mounting Assemblies

STANDARD MOUNTING ASSEMBLY

1.Place mounting flange (1) over the existing collar adaptor connection lip or sink bowl flange (this may require some force).

2.Push the mounting flange up out of the way and fit the groove in the mounting gasket (2) onto the . connection lip. Make sure the gasket is fully seated . on the flange.

3.Push the mounting flange down over the mounting gasket, fitting the threaded mounting flange fasteners into the recesses in the top of the mounting gasket.

#6 Collar Adaptor

(1)Mounting Flange

(2)Mounting Gasket

(3) Flat Gasket

Disposer Body Flange

1/4” Screw

Figure 6. #6 Mounting Assembly

4.From the bottom, insert two screws through opposite sides of the flat gasket (3) and mounting flange, into the threaded fasteners in the existing flange. The flat gasket is used only in the #6 mounting assembly. The screws should protrude about 1/4" below the mounting gasket.

5.Position the disposer beneath the mounting gasket and raise it to engage the two protruding screws in the disposer body flange keyhole slots. Secure the remaining screws and position the disposer correctly for the plumbing connections. If disposer legs are included, adjust the legs to support the disposer.

#7 Collar Adaptor

(1) Mounting Flange

(2) Mounting Gasket

Disposer Body Flange

1/4” Screw

Figure 7. #7 or Sink Bowl Mounting Assembly

SPECIAL INSINKERATOR MOUNTING ASSEMBLIES

When installing an InSinkErator Foodservice disposer to a non-InSinkErator sink bowl, a special mounting adaptor kit is required. The special mountings are described in the Mounting Adaptor Selection Guide (for more information, call 1-800-845-8345 or go to www.insinkerator.com). Figures 8-10 show examples of non-InSinkErator style sinks. (Mounting instructions are included in each special mounting adaptor kit.)

6:8. Outward Flange

Figure 7:

Figure 8: Straight Flange

Figure

Figure 9. Inward Flange

Figure 10. Straight Flange

8

Image 7
Contents Part.No..14481.Rev..A Table of Contents Introduction WarrantyIntroduction/Typical Installation Typical InstallationFeatures Waste Xpress FeaturesMounting the Control Center WX-101A Control Features/Mounting Control CenterPersonal Injury Installing DisposerInSinkErator Mounting Assemblies Standard Mounting AssemblySpecial Insinkerator Mounting Assemblies Top View Installing the Waste XpressElectrical Connections Waste Xpress LocationWaste Inlet Line Plumbing ConnectionsRouting Water Flow Waste Outlet LinePlumbing Connections Water Supply ConnectionsLine Voltage Electrical ConnectionsPRE-OPERATION Test Operating InstructionsTo Start Operational Tips Operating Waste Xpress SystemBearing Bracket Cleaning InstructionsSystem Troubleshooting TroubleshootingIntended for use in the event of control System Troubleshooting Disposer Troubleshooting Waste Xpress Troubleshooting Other types of food waste and/or disposables 120 208/230 Phase To 2 HP Waste Xpress 208/230V, 3Phase System Wiring DiagramWX101A-3 208/230V 3Phase Electrical Connections 120 380/460 Phase To 2 HP Waste Xpress 380/460V, 3Phase System Wiring DiagramWX101A-4 380/460V 3Phase Electrical Connections 230 volt 3 Phase 460 volt 3 Phase Motor Wiring Diagram

14481 specifications

The InSinkErator 14481 is a standout model in the realm of food waste disposers, known for its powerful performance and innovative features. Designed for both residential kitchens and professional use, it effectively transforms food scraps into fine particles that are easily disposed of through the plumbing system.

One of the hallmark features of the InSinkErator 14481 is its robust motor. With a high-speed operation reaching 3,450 RPM, it efficiently grinds food waste, ensuring that even fibrous materials like celery and potato peels are easily pulverized. This not only minimizes the risk of clogs in your plumbing but also reduces odors that can arise from food waste sitting in a trash bin.

The unit utilizes a patented SoundSeal technology, which significantly dampens noise during operation. This feature makes it an excellent choice for home kitchens where peace and quiet are desired, as it addresses one of the common concerns associated with food disposers - the noise level. Users can enjoy peace of mind knowing their kitchen remains tranquil even while they manage food waste.

Another key characteristic of the InSinkErator 14481 is its multi-grind technology. This allows for a more versatile grinding capability, meaning the disposer can handle a wider variety of food types with ease. Whether it's tough meats, fibrous vegetables, or even small bones, this model excels in pulverizing waste, making post-meal cleanup a breeze.

Installation of the InSinkErator 14481 is straightforward, as it comes with a convenient Quick Lock mounting system, enabling easy attachment to standard sink flanges. This feature is invaluable for homeowners who may want to install the unit themselves or replace an older model with minimal hassle.

In terms of build quality, the InSinkErator 14481 is constructed using durable materials designed to withstand the rigors of daily use. Its powerful motor is backed by a generous warranty, reflecting the manufacturer's confidence in its longevity and performance.

In conclusion, the InSinkErator 14481 is a highly efficient food waste disposer that combines power, innovation, and convenience. Its features, including a high-speed motor, SoundSeal technology, and multi-grind capabilities, make it an ideal choice for anyone looking to simplify kitchen cleanup while enhancing sustainability efforts by reducing food waste.