InSinkErator 14481 manual Waste Xpress Location, Electrical Connections

Page 9

Installing the Waste Xpress

WASTE XPRESS LOCATION

NOTE: Prior to installing the Waste Xpress the disposer and control center should be installed as specified within this manual.

Position Waste Xpress within 10 feet of the disposer outlet flange. A maximum of four (4) 90º elbows can be used between the disposer and Waste Xpress .

(prefer 45º elbow).

Level Waste Xpress by turning the legs in or out with a wrench. Place a level on top of the unit.

ELECTRICAL SHOCK

Ensure that Waste Xpress voltage and phase match that of the electrical supply, control center &. disposer. Check nameplate for specification.

Electrical connections should be made by a . qualified electrician and should comply with all . local codes.

Turn off electrical supply to Waste Xpress, . control center & disposer before attempting to work on it. Test with a volt meter or circuit tester . to ensure that power is off.

Do not operate unit with panels removed.

All components (disposer, WX, control center . and solenoids) must be carefully and permanently grounded.

A properly fused disconnect must be installed at Waste Xpress, control center & disposer electrical supply source.

Use only NEMA 4 watertight electrical connectors when connecting to junction box.

ELECTRICAL CONNECTIONS

The Waste Xpress system requires power only to the control center. The control center powers the disposer and Waste Xpress.

1.Remove retaining screw and disposer . electrical cover.

2.Open control center cover by loosening locking clamps securing it.

3.Remove terminal cover from Waste Xpress . (see Figure 13).

4.Connect incoming power line to electrical door . disconnect switch in WX-101A.

5.Connect disposer motor leads to terminal . block locations.

6.Connect cold water solenoid to appropriate. terminals 4 and 13. Connect hot water solenoid to terminal 18 and 7.

7.Connect wire bundle between WX-101A and . Waste Xpress unit as detailed in wiring diagram. Door interlock connections are #3 and #95. Replace terminal cover.

8.Wire per local electrical codes and install . using NEMA 4 watertight electrical connectors . (not supplied).

9.Install disposer terminal box cover and secure with retaining screw.

10.Secure WX-101A cover with locking clamps.

ELECTRICAL SHOCK

Do not pinch or damage the electrical wires when installing the terminal box.

 

 

 

 

 

 

WX

 

WX-101A

Voltage

 

 

 

 

Terminal

 

Terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WX Auger Motor.

 

 

T1, T2, T3

To

T1, T2, T3

Line

3 Phase

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WX Magnetic .

 

 

3, 95

 

To

3, 95

24V

Interlock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cold Water Solenoid

 

 

 

 

 

 

 

 

 

 

 

4, 13

24V

(Disposer)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hot Water Solenoid

 

 

 

 

 

 

 

 

 

 

 

7, 18

24V

(WX Spray)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disposer

 

 

 

 

 

 

 

 

 

 

To

See Diagrams

Line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminal

Cover

Figure 13.

Captive

Fasteners

Auger

Screen

Waste Inlet

Waste Outlet

Figure 14. Cover Removed

10

Image 9
Contents Part.No..14481.Rev..A Table of Contents Introduction/Typical Installation WarrantyTypical Installation IntroductionFeatures Waste Xpress FeaturesMounting the Control Center WX-101A Control Features/Mounting Control CenterPersonal Injury Installing DisposerStandard Mounting Assembly InSinkErator Mounting AssembliesSpecial Insinkerator Mounting Assemblies Top View Installing the Waste XpressElectrical Connections Waste Xpress LocationWaste Inlet Line Plumbing ConnectionsPlumbing Connections Waste Outlet LineWater Supply Connections Routing Water FlowLine Voltage Electrical ConnectionsPRE-OPERATION Test Operating InstructionsTo Start Operational Tips Operating Waste Xpress SystemBearing Bracket Cleaning InstructionsSystem Troubleshooting TroubleshootingIntended for use in the event of control System Troubleshooting Disposer Troubleshooting Waste Xpress Troubleshooting Other types of food waste and/or disposables 120 208/230 Phase To 2 HP Waste Xpress 208/230V, 3Phase System Wiring DiagramWX101A-3 208/230V 3Phase Electrical Connections 120 380/460 Phase To 2 HP Waste Xpress 380/460V, 3Phase System Wiring DiagramWX101A-4 380/460V 3Phase Electrical Connections 230 volt 3 Phase 460 volt 3 Phase Motor Wiring Diagram

14481 specifications

The InSinkErator 14481 is a standout model in the realm of food waste disposers, known for its powerful performance and innovative features. Designed for both residential kitchens and professional use, it effectively transforms food scraps into fine particles that are easily disposed of through the plumbing system.

One of the hallmark features of the InSinkErator 14481 is its robust motor. With a high-speed operation reaching 3,450 RPM, it efficiently grinds food waste, ensuring that even fibrous materials like celery and potato peels are easily pulverized. This not only minimizes the risk of clogs in your plumbing but also reduces odors that can arise from food waste sitting in a trash bin.

The unit utilizes a patented SoundSeal technology, which significantly dampens noise during operation. This feature makes it an excellent choice for home kitchens where peace and quiet are desired, as it addresses one of the common concerns associated with food disposers - the noise level. Users can enjoy peace of mind knowing their kitchen remains tranquil even while they manage food waste.

Another key characteristic of the InSinkErator 14481 is its multi-grind technology. This allows for a more versatile grinding capability, meaning the disposer can handle a wider variety of food types with ease. Whether it's tough meats, fibrous vegetables, or even small bones, this model excels in pulverizing waste, making post-meal cleanup a breeze.

Installation of the InSinkErator 14481 is straightforward, as it comes with a convenient Quick Lock mounting system, enabling easy attachment to standard sink flanges. This feature is invaluable for homeowners who may want to install the unit themselves or replace an older model with minimal hassle.

In terms of build quality, the InSinkErator 14481 is constructed using durable materials designed to withstand the rigors of daily use. Its powerful motor is backed by a generous warranty, reflecting the manufacturer's confidence in its longevity and performance.

In conclusion, the InSinkErator 14481 is a highly efficient food waste disposer that combines power, innovation, and convenience. Its features, including a high-speed motor, SoundSeal technology, and multi-grind capabilities, make it an ideal choice for anyone looking to simplify kitchen cleanup while enhancing sustainability efforts by reducing food waste.