Haier WQP12-CBE3 manual Loading the Dishwasher Starting the Appliance

Loading the Dishwasher GB

Starting the Appliance

GB

Before placing the dishes in the dishwasher, remove the larger food debris to prevent the filter from becoming clogged, which results in reduced performance.

If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they be allowed to soak before they are washed. This will eliminate the need for extra wash cycles.

Pull out the rack to facilitate loading the dishwasher.

Lower Rack Upper Rack

Starting a wash cycle

After having completed all of the installation steps in the preced- ing paragraphs, turn on the water to the unit, partially open the door of the dishwasher, and press the ON-OFF button "A" lo- cated on the control panel. The "B" indicator light will come on. At this point, the appliance is on and ready to be programmed.

If you forget to load some of the dishes...

The wash cycle can be interrupted by opening the door carefully (in order to avoid being sprayed by hot water). When the door is closed again, the cycle will automatically restart at the point where it left off.

How to Use the Lower Rack

We recommend that you place the most difficult to clean items on the bottom rack: pots ,lids, serving dishes and bowls, as shown in the figure to the right.

It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm.

-Pots, serving bowls, etc. must always be placed face down.

-Deep pots should be slanted to allow the water to flow out.

-The cutlery basket can be doubled so that only one section may be used when the cutlery ware load is light. This also makes space for additional pots and pans, and it can also be placed in the upper rack.

-Cutlery should be placed in the cutlery basket with the handles at the bottom; if the rack has side baskets, the spoons should be placed individually into the appropriate slots. Espe- cially long utensils should be placed in the horizontal position at

Howthe frtontUseof thetheupperUpperrackRack.

The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty).

- Position the dishes and cookware so that they do not get moved by the spray of water.

The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see fig.A).

Load for 12 Standard Settings

Green/Yellow

	Blue
	Brown
Fig.A	Fig.B

Setting and Starting a wash Cycle

Choose the desired cycle by pressing the cycle selection button "P". Each time it is pressed, one of the cycle indicator lights "D" will come on in succession.

Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table con- tained in this manual, especially when first using the appliance). Close the door and after a few seconds, a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancel- ling or modifying a cycle while underway. "The end of the cycle will be signalled by a double acoustic sound, and the indicator light "D" will begin to blink.

Cancelling or modifying a cycle while underway...

Premise: A cycle that is underway can only be modified if it has only been running for a short time.

Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent").

To change the cycle currently underway, open the door, press the "P" programming button and hold it in for about 5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short acoustic sound and the relative indicator light will turn off.

At the end of the wash cycle...

The end of the cycle will be indicated by a double acoustical signal and the blinking of the "D" indicator light. Open the door, turn off the appliance using the ON/OFF switch and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results.

Warning

Important wiring instructions for plug UK only

WARNING: THIS APPLIANCE MUST BE BARTHED

The cords in this mains lead are coloured in accordance with the following code: (see fig.B)

*Green/Yellow *Earth *Blue *Neutral *Brown *Live

*The core which is coloured GREEN/YELLOW must be connected to the terminal which is marked with the letter E or by the earth symbol or coloured GREEN/YELLOW.

*The core which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

*The core which is coloured BROWN must be connected to the termi- nal which is marked with the letter .

To set a new wash cycle, follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle."

Connecting instructions	If the terminals of your 3 pin plug are unmarked or if your
As the colours of the cores in the mains lead of this appliance	installation is fitted with a 2 pin plug,consult a qualified
may not correspond with the coloured markings indentifying the	electrician.
terminals in your plug proceed as follows:	If a 10 AMP plug is fitted,fit 53 AMP fuse.

.5. .6.