Haier WQP12-AFM2 manual Cleaning and Special Maintenance, Close-up View Interior Troubleshooting

Cleaning and Special Maintenance

Filter Assembly

For the best performance and results, the filter assembly must be cleaned.

The filter efficiently removes food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the "A" semi-circular filter and cup under running water. To remove the filter assembly, pull on the cup handle in the upward direction. The entire filter as- sembly (made up of the "A" semicircular filter and the "B" fine filter) should be cleaned at least once a month. To clean the filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as shown in the figures below and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.

The dishwasher must never be used without the filters. Improper replacement of the filters may reduce level of the appliance and damage dishes and utensils.

Cleaning the Spray Arms

It may happen that food particle become encrusted on the sprayer arms and block the hole. Check the sprayer arms periodically and clean them when needed. (See "Close up view [interior]" , letters C-E ).

B

A

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 1/A) located on the outlet of the water supply tap.

After turning off the water tap, unscrew the end of the water sup- ply hose, remove the filter and clean it carefully under running water. Then, return the filter to its place and tighten the water supply hose back into position.

Close-up View (Interior)

Troubleshooting

It may occur that the dishwasher does not function or does not	- the water supply to the house on and has
function properly. Before calling for assistance, Iet us see what	sufficient pressure;
can be done first: have you forgotten to press one of the buttons	- the water supply hose is crimped or bent;
or to perform an essential operation?	- the filter for the water supply hose is clogged.

A	Upper Rack	E	Bottom Spray Arm
B	Rack Height Adjustor
		F	Washing Filter
C	Top Spray Arm
		G	Detergent and Rinse Aid Dispenser
D	Lower Rack
		H	Salt Container Cap

The Dishwasher Does Not Start

Have you checked whether:

-the plug is pushed into the socket correctly;

-the power is on in the house;

-the door is closed properly;

-the ON-OFF switch is on "ON";

-the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

-the water is turned on and the hose is connected properly;

-the water supply to the house on and has sufficient pressure;

-the water supply hose is crimped or bent;

-the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you checked whether:

-the water is turned on and the hose is connected properly;

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

-the lid to the salt container is closed properly;

-the rinse aid dosage is correct.

If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised ser- vice centre and provide them with the following information:

-the nature of the problem;

-the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door.

Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts.

Technical characteristics

Width	60 cm
Depth	60 cm
Height	85 cm
Capacity	12 standard place settings
Mains water pressure	0.03-0.6 MPa
Power voltage	220V~50Hz
Total absorber power	1950W

.9.

GB

GB

.2.