Extron electronic MDA 4V EQ, MDA 4SV EQ, MDA 2V EQ For a smaller or larger pole Locally obtain a

Page 12

Installation and Operation, cont’d

5.

Place the U-bolt around the ceiling pole and insert the two

 

legs of the U-bolt through the round holes in the

 

contoured base, then through the slotted holes in the

 

bracket’s mounting plate.

 

•

For a typical (1.5" to 2.0" diameter) pole — You can

 

 

use the supplied U-bolt, which fits a typical ceiling

 

 

pole.

 

•

For a smaller or larger pole — Locally obtain a

 

 

U-bolt that fits your ceiling pole. The slotted holes

 

 

on the bracket can accommodate a U-bolt for pole

 

 

sizes from 1.0" to 2.5" in diameter.

6.

Secure the bracket to the U-bolt with the included hex

 

nuts.

 

PMK 350 Projector Mounting Kit

The PMK 350 Low Profile Projector Mounting Kit is an above- projector mounting kit that attaches to a 1.5" to 2" diameter projector mounting pole. It can hold more than one device, in a variety of sizes.

The PMK 350 is available in black (part #70-563-02) or white (part #70-563-03).

Follow these steps to mount the MDA EQ on the PMK 350:

1.

Remove the front panel from the PMK, using a #2 Philips

 

screwdriver. Retain the four screws to reattach the plate

 

when finished.

2.

Remove any rubber feet from the bottom of the MDA EQ.

3.

Secure the MDA to one side of the mounting bracket, using

 

two of the supplied 4-40 x 3/16" screws in opposite

 

(diagonal) corners. Use an Extron Tweeker (provided) or a

 

Philips #1 screwdriver to tighten the screws.

4.

Using the two included tie wraps, strap the MDA EQ

 

power supply to the PMK bracket.

5.

If desired, remove the back panel of the PMK 350 and

 

mount an additional MDA or other device(s) at the back of

 

the bracket, as described in step 3.

6.

Place the PMK 350 mounting tray around the projector

 

ceiling mounting pole. (See the illustration on the next

 

page.)

 

Mount Plate

 

 

Flange

Extron

 

 

Rear Plate

 

MDA EQ Series

 

Mounting Tray

Mini Distribution Amplifier

 

 

 

 

Contoured

 

 

Base

 

 

L-shaped

 

 

Bracket

Extron

U-bolt

 

PMK 350

 

 

 

Multi-product Projector

Mounting Kit

Extron

Power Supply

Front Plate

Overlay Sheet

Mounting the MDA EQ using the PMK 350

Projector Mounting Kit

7.

Assemble the U-bolt and the following parts in the order

 

they are listed below:

 

a.

Pass the legs of the U-bolt through the slotted holes

 

 

on the back of the mount plate flange.

 

b.

Place the U-bolt legs around the ceiling pole.

 

c.

Pass the U-bolt legs through the round holes in the

 

 

contoured base.

 

 

 

Place the contoured base against the pole and

 

 

 

 

 

 

opposite the mount plate flange. The pole

 

 

 

should fit snugly into the depression in the

 

 

 

center of the contoured base.

 

d.

Pass the U-bolt legs through the round holes in the

 

 

L bracket.

8.

Align the two round holes in the bottom of the L bracket

 

with the two slotted holes in the base of the PMK 350, on

 

either side of the opening for the pole; and attach the L

bracket to the base by inserting the two provided 6-32 x 5/16" screws through the aligned slots. Tighten the screws slightly; you should still be able to slide the L bracket to adjust it as needed.

2-8

VersaTools® MDA EQ Series • Installation and Operation

VersaTools® MDA EQ Series • Installation and Operation

2-9

Page 11 Page 13
Image 12
Page 11 Page 13
Contents User’s Manual VersaTools Video Mini Distribution AmplifiersPrecautions Extron’s WarrantyFCC Class a Notice 噝 Quick Start Guide MDA EQ Series Projector Mounting Bracket Mounting BoltTable of Contents Table of Contents, cont’d MDA EQ SeriesIntroduction About this ManualAbout the MDA EQ Series Mini Distribution Amplifiers Two Introduction, cont’dInstallation and Operation Mounting the MDA EQ SeriesTabletop use Rack mountingInstallation and Operation, cont’d Furniture mountingProjector mounting Mounting an MDA EQ on a 6-inch rack shelfPMK 300 Projector Mounting Kit Mounting the MDA EQ using the PMK Projector Mounting Kit For a smaller or larger pole Locally obtain aRear Panel Features and Cabling MDA 2V EQ rear panelMDA 4V EQ rear panel MDA 4SV EQ rear panelFront Panel Features and Operation Power connector wiringMDA 2V EQ front panel MDA 4V EQ front panelAAppendix a Specifications, Parts, and Accessories Specifications, Parts, and Accessories, cont’d Models Optional AccessoriesIncluded Parts Specifications, Parts, and Accessories, cont’d Specifications, Parts, and Accessories, cont’d
Related manuals
Manual 14 pages 40.02 Kb

MDA 2V EQ, MDA 4SV EQ, MDA 4V EQ specifications

Extron Electronics is renowned for its innovative solutions in the field of professional audiovisual technology. Among its diverse lineup of products, the MDA 2V EQ, MDA 4SV EQ, and MDA 4V EQ stand out as exceptional multi-distribution amplifiers designed to enhance signal processing and distribution in various AV settings.

The MDA 2V EQ is a two-channel distribution amplifier that excels in providing high-quality video and audio signal distribution. It is equipped with advanced equalization capabilities that allow users to fine-tune signal levels for optimal performance over long cable runs. The MDA 2V EQ supports a wide range of video formats, including composite, S-video, and component, ensuring compatibility with various equipment. Its compact design makes it easy to integrate into existing AV setups, while its robust construction ensures reliability in demanding environments.

The MDA 4SV EQ, on the other hand, is a four-channel distribution amplifier specifically designed for S-video signals. This model also features EQ for tailoring the output levels to match varying distances between the source and the display devices. By providing four isolated outputs, it ensures that each connected device receives a clean and undistorted signal. The MDA 4SV EQ is ideal for applications that demand high-quality S-video distribution, such as corporate presentations or educational content delivery.

Meanwhile, the MDA 4V EQ extends Extron’s commitment to versatile AV solutions with its four-channel capability focused on composite video signals. Similar to its counterparts, this model includes built-in EQ, enabling precise signal adjustments. Its ability to drive multiple outputs without compromising signal integrity makes it a perfect choice for situations requiring extensive video distribution.

All three models incorporate Extron’s proprietary technologies, ensuring minimal signal degradation and enhanced performance. They feature user-friendly troubleshooting tools such as LED indicators for signal presence and power status. Additionally, these amplifiers are designed with thermal protection to avoid overheating during extended use.

In summary, the Extron MDA 2V EQ, MDA 4SV EQ, and MDA 4V EQ offer a range of features tailored for optimal video and audio distribution in professional settings. Their advanced signal management technologies, robust performance, and user-friendly design make them invaluable tools for AV professionals looking to achieve high-quality signal distribution in diverse applications.
Top Page Image Contents