Grindmaster 3511 manual How to Clean Exposed Filter Air-Cooled Unit Only, How to Adjust Belt

Page 15
Figure FF

How to Clean Condenser (Air-Cooled Unit Only)

NOTE: Loss of refrigeration efficiency will result if condenser is allowed to become dirty. Excessive compressor run time or loss of capacity are a good indication that the condenser needs to be cleaned.

1.Disconnect electrical power.

2.Remove side panels.

3.Place a damp towel over the side of the condenser opposite the fan motor.

4.Use compressed air or CO2 blow out dirt from the fan side of the condenser. An alternate cleaning method is to use a condenser brush and vacuum cleaner.

!CAUTION: Procedure can create a loud noise.

How to Clean Exposed Filter (Air-Cooled Unit Only)

1.Slide exposed filter out of the rails by pulling forward on the filter. It is recommended to remove the filter by using the palm of your hand and applying even pressure to the face of the filter.

2.Clean filter with liquid soap and water.

3.Soak filter for 15 minutes.

4.Rinse filter with heavy stream of water, opposite the direction of air flow. Allow filter to dry.

5.Slide the filter into the rails until the filter contacts the stop on the top rail.

How to Clean Concealed Filter (Air-Cooled Unit Only)

1.For concealed filters lift lid and pull up on filter tab to remove filter.

2.Clean filter with liquid soap and water.

3.Soak filter for 15 minutes.

4.Rinse filter with heavy stream of water, opposite the direction of air flow. Allow filter to dry.

5.Slide filter into top of filter cover with removal clip up and the air flow arrows facing the existing panel.

How to Adjust Belt

CAUTION: Unplug the machine before performing any adjustments. This procedure must be done by a ! qualified technician.

Check the belt tension. The proper belt deflection is 1/2” over all. If the deflection is more than 1/2” the motor will need to be lowered. If the deflection is less than 1/2”, the motor will need to be raised. Follow this procedure to adjust the motor to achieve proper belt tension. (See Figure FF)

1.Unplug the machine and remove both side and rear panels.

2.Locate the motor flange bearings. These are the side mounted bearings that hold the motor to the cradle. The motor is double shafted and the shaft extends through a bearing on each end. The bearing is held to the motor cradle by two allen bolts on each bearing.

3. Loosen the allen bolts on each bearing. Do not loosen the setscrews that hold the bearing collar to the motor shaft.

4.Lower the motor or raise the motor as needed. The motor must be kept level from front to back. Do not lower or raise only one end of the motor. This will result in excessive belt wear and belt noise.

5.Tighten all four allen bolts down. Align the motor pulley with the top pulley if needed.

6.The motor pulley should be in alignment with the large (driven) top pulley. Use a straight edge along the top pulley.

7.If the pulleys are not in alignment, loosen the setscrew on the motor pulley and move either in or out as needed.

8.Tighten the setscrew back down on the motor shaft (use of non-permanent loc-tite is recommended). Please be sure the setscrew is tightened down on the flat surface of the motor shaft.

9.Return the unit back to service.

How to Change Back Lit Sign Merchandiser Bulb

1.Remove the two screws, located on the top of either side of the sign.

2.Lower the metal enclosure that frames the merchandiser insert.

3.Pull merchandiser enclosure down and out.

4.Replace bulb inside.

5.Reassemble. For ease of assembly, put merchandiser in light box before placing metal enclosure back on.

Model 3511

Page 13

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model 3511 Beverage Freezer Manual Page Table of Contents Product Tips OPERATOR’S Safety PrecautionsFreezer Application and Specifications ModelCarburetor Assembly Freezer SpecificationsMix Considerations General Shipment Transit InstallationReview hopper contents to make sure all parts are available Mix Low Function Operation and AdjustmentsAccessory Installation How to OperateFigure J Consistency AdjustmentCare and Cleaning Disassembly and CleaningDrain and Rinse Tight. Do not use tools to tighten knobs Figure CC Insert Retaining Pin Sanitizing and RefillingParts Replacement Schedule MaintenanceClean-In-Place Procedure Daily Cleaning Suggested Daily MaintenancePreventative Maintenance Procedure Every 6 to 12 Months How to Change Back Lit Sign Merchandiser Bulb How to Clean Exposed Filter Air-Cooled Unit OnlyHow to Clean Concealed Filter Air-Cooled Unit Only How to Adjust BeltProblem Probable Cause Remedy General TroubleshootingCheck List Exploded View Model Model Base Assembly Model Electrical Box Assembly Model 3511 Wiring Diagram Model 3511 Compressor Wiring Model 3511 Ladder Diagram Model 3511 Spinner Wiring Model 3511 Refrigeration Model 3511 Refrigeration Schematic Model Grindmaster Corporation Form # WH-305-02 W0600114

3511 specifications

The Grindmaster 3511 is a state-of-the-art commercial coffee grinder that has become a staple in cafes, restaurants, and specialty coffee shops around the world. Known for its exceptional performance and reliability, the Grindmaster 3511 showcases several key features and technological advancements that cater to the demands of both baristas and coffee enthusiasts.

One of the most notable features of the Grindmaster 3511 is its precision grinding capabilities. The grinder is equipped with high-quality flat burrs that ensure a uniform grind size, which is essential for optimal extraction and the development of rich and flavorful coffee profiles. With adjustable grind settings, users can easily switch from espresso to French press grinds, accommodating various brewing methods and preferences.

The Grindmaster 3511 has a robust construction designed for heavy use in commercial settings. The grinder’s durable materials and components ensure longevity and consistent performance, allowing it to withstand the rigors of daily operation. This reliability is complemented by an efficient motor that operates quietly, making it suitable for environments where customer experience is paramount.

In terms of technology, the Grindmaster 3511 features an intuitive digital interface that simplifies the grinding process. The built-in timer allows baristas to set precise grind times, ensuring consistent doses for each brew. This precision is crucial in maintaining the quality and flavor of the coffee, which can vary significantly with inconsistent grind sizes.

Additionally, the Grindmaster 3511 is designed with user-friendly maintenance features. The removable grind chamber and easy access to critical components make cleaning and upkeep straightforward, promoting hygiene and prolonging the life of the grinder. This ease of maintenance is particularly beneficial for busy establishments where time is of the essence.

Moreover, the Grindmaster 3511 integrates safety features such as an automatic shut-off system, which helps prevent overheating and protects the motor during prolonged use. This attention to safety and efficiency ensures that the grinder not only meets but exceeds industry standards.

Overall, the Grindmaster 3511 stands out for its combination of precision, durability, and ease of use. Its advanced grinding technology and thoughtful design make it a valuable investment for any coffee business aiming to deliver high-quality beverages consistently. With the Grindmaster 3511, users can expect a reliable grinding experience that enhances the overall coffee-making process.
Top Page Image Contents