Grindmaster 3511 OPERATOR’S Safety Precautions, Freezer Application and Specifications, Model

Page 4

OPERATOR’S SAFETY PRECAUTIONS

IMPORTANT: Failure to comply with the following safety precautions may result in severe personal injury or damage to the machine.

1.Read and understand the operating instructions in this manual thoroughly. Only allow properly trained persons to operate this machine.

2.Note all warning labels on the freezer. If any warning labels are missing or damaged replace them immediately.

3.Do not wear loose fitting garments or jewelry which could cause a serious accident.

4.Stay alert at all times during operation.

5.Keep operating area clean.

6.Do not attempt any repairs unless the main power supply to the freezer has been disconnected. Contact Grindmaster Technical Service for service assistance.

7.Do not put objects or fingers in the dispense plunger.

8.Do not operate freezer if any excessive noise or vibration occurs. Contact your authorized service agent.

9.Be certain machine is installed with adequate space for proper air circulation. (See installation section.) Failure to provide sufficient ventilation will reduce freezer performance and void equipment warranty.

Located on the right, left and rear panels. (part # W0600218)

FREEZER APPLICATION AND SPECIFICATIONS

Model 3511

The freezer consists of a freezing cylinder with a rotating internal auger (dasher) that is belt-driven by an electric motor. The auger scrapes frozen product off of the inside of the refrigerated cylinder. A torque sensing mechanism controls compressor operation to maintain desired product consistency. The freezer utilizes an air-cooled refrigera- tion system to freeze the product. A self-closing dispensing valve is attached to the front of the freezing cylinder. The unit has an adjustable consistency control and an out of product indicator.

When properly operated and cared for, the Model 3511 will provide many years of service. Proper care includes regular cleaning and maintenance. To minimize the amount of maintenance necessary, follow the operating procedures outlined in this manual.

Product Tips

The Model 3511 was designed to dispense a wide variety of frozen beverages including frozen fruit juice, frozen lemonade, slush and frozen cocktails. These products can be served in consistencies ranging from thin to fairly thick.

Two types of dispensing valve plungers and product consistency springs are available depending on the thickness of the product being served. These parts are interchangeable depending upon your needs. One plunger, part W0480438 has one horizontal outlet slot and is used to serve thin to medium products such as frozen lemonade and slush. The other plunger, part W0480451 has two horizontal outlet slots and is used to serve thicker product such as neutral base frozen cocktails. A red spring, part W0631239, is used on the drive motor to adjust product consistency to serve thin to medium products. The yellow spring, part W0631238, is used for thicker product. The spring is locat- ed next to the drive motor behind the right hand side panel.

Over an extended period of time, some products, such as frozen cocktails that contain alcohol, have a tendency to separate, or stratify. Separation of product on the mix storage hopper can result in frozen product quality inconsis- tency. Simply keeping the product, in the mix storage hopper, stirred on a regular basis will eliminate this problem.

Page 2

Model 3511

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model 3511 Beverage Freezer Manual Page Table of Contents OPERATOR’S Safety Precautions Freezer Application and SpecificationsModel Product TipsFreezer Specifications Carburetor AssemblyMix Considerations General Installation Shipment TransitReview hopper contents to make sure all parts are available Operation and Adjustments Accessory InstallationHow to Operate Mix Low FunctionConsistency Adjustment Figure JDisassembly and Cleaning Care and CleaningDrain and Rinse Tight. Do not use tools to tighten knobs Sanitizing and Refilling Figure CC Insert Retaining PinMaintenance Clean-In-Place Procedure Daily CleaningSuggested Daily Maintenance Parts Replacement SchedulePreventative Maintenance Procedure Every 6 to 12 Months How to Clean Exposed Filter Air-Cooled Unit Only How to Clean Concealed Filter Air-Cooled Unit OnlyHow to Adjust Belt How to Change Back Lit Sign Merchandiser BulbGeneral Troubleshooting Problem Probable Cause RemedyCheck List Exploded View Model Model Base Assembly Model Electrical Box Assembly Model 3511 Wiring Diagram Model 3511 Compressor Wiring Model 3511 Ladder Diagram Model 3511 Spinner Wiring Model 3511 Refrigeration Model 3511 Refrigeration Schematic Model Grindmaster Corporation Form # WH-305-02 W0600114

3511 specifications

The Grindmaster 3511 is a state-of-the-art commercial coffee grinder that has become a staple in cafes, restaurants, and specialty coffee shops around the world. Known for its exceptional performance and reliability, the Grindmaster 3511 showcases several key features and technological advancements that cater to the demands of both baristas and coffee enthusiasts.

One of the most notable features of the Grindmaster 3511 is its precision grinding capabilities. The grinder is equipped with high-quality flat burrs that ensure a uniform grind size, which is essential for optimal extraction and the development of rich and flavorful coffee profiles. With adjustable grind settings, users can easily switch from espresso to French press grinds, accommodating various brewing methods and preferences.

The Grindmaster 3511 has a robust construction designed for heavy use in commercial settings. The grinder’s durable materials and components ensure longevity and consistent performance, allowing it to withstand the rigors of daily operation. This reliability is complemented by an efficient motor that operates quietly, making it suitable for environments where customer experience is paramount.

In terms of technology, the Grindmaster 3511 features an intuitive digital interface that simplifies the grinding process. The built-in timer allows baristas to set precise grind times, ensuring consistent doses for each brew. This precision is crucial in maintaining the quality and flavor of the coffee, which can vary significantly with inconsistent grind sizes.

Additionally, the Grindmaster 3511 is designed with user-friendly maintenance features. The removable grind chamber and easy access to critical components make cleaning and upkeep straightforward, promoting hygiene and prolonging the life of the grinder. This ease of maintenance is particularly beneficial for busy establishments where time is of the essence.

Moreover, the Grindmaster 3511 integrates safety features such as an automatic shut-off system, which helps prevent overheating and protects the motor during prolonged use. This attention to safety and efficiency ensures that the grinder not only meets but exceeds industry standards.

Overall, the Grindmaster 3511 stands out for its combination of precision, durability, and ease of use. Its advanced grinding technology and thoughtful design make it a valuable investment for any coffee business aiming to deliver high-quality beverages consistently. With the Grindmaster 3511, users can expect a reliable grinding experience that enhances the overall coffee-making process.
Top Page Image Contents