Grindmaster RAPS400E, RAPS300E, RAP400E, RAP300E Drain Water Tank, Remove Brew Valve, Remove Heater

Page 10

Service (con't)

Drain Water Tank

Always empty the tank before shipping.

WARNING

Draining of tank should be performed by a qualified service technician. The tank contains very hot water. May cause severe burns.

Note: Brewer may contain over 5 gallons of hot water.

1)Prepare a heat resistant container to drain tank water into.

2)Shut off power to the brewer.

3)Remove the front access panel.

4)Pinch or clamp the silicone hose connected to fill valve.

5)Disconnect hose from outlet barb on fill valve.

6)Place hose over drain and release clamp.

7)Allow the tank to drain completely.

NOTE: It may be necessary to pinch the hose and stop the water before container is full. Carefully reinstall hose over fill valve outlet, then empty container. Repeat steps 4-7 completely to drain tank.

Remove Brew Valve

1)Disconnect electric power to machine.

2)Remove top cover and remove wires and small tube from valve.

3)Tilt inlet of valve down and pull sideways out of spray tee.

4)Clamp rubber tubing and disconnect valve from tubing.

Remove Heater

1)Disconnect power and remove top cover of brewer.

2)Disconnect wire leads to heater.

3)Remove tank cover by loosening retaining screw. Cover is lifted up with heater attached. Heater is then removed.

4)Replace heater with sealing washers in same configuration. When tightening nuts, hold element so it does not twist.

5)Replace tank cover ensuring O-ring seal is good.

6)Replace heater wires. Be sure all electrical connections are secure.

Shuttle Brewers & Airpot/Shuttle Brewers

Page 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Shuttle Brewer & Airpot/Shuttle Brewers Start-up InstallationElectric Hook-up Shuttle Brewers & Airpot/Shuttle BrewersOperation HOT Liquid HazardBrew Volume, Brew Timer AdjustmentsAdjusting the Timer Two Batch Timer with Knob Adjustment, See Figure To Adjust the Bypass Thermostat AdjustmentShuttle Brewers & Airpot/Shuttle Brewers After Each Brew CleaningEvery Day Service Weekly or Bi-Weekly, Depending on UseRemove Brew Valve Drain Water TankRemove Heater Troubleshooting Filling, Heating, and Brewing Filling ProblemsRecovery time is Problem Possible Cause Service Check Remedy Brew volume too Parts Illustration for Models P300E & P400E DescriptionParts Illustration for Model RAP400E Momentary Switch Parts Illustration for Model RAPS400EParts Illustration for Model VSB-400 Parts Illustration for Shuttle CS-LL LID Stopper W/ O-RINGRough-In Drawing for Model P-300 Rough-In Drawing for Model P-400 Rough-In Drawing for Model RAP-300 Rough-In Drawing for Model RAP-400 Rough-In Drawing for Model RAPS-300 Rough-In Drawing for Model RAPS-400 Rough-In Drawing for Model VSB-300 Rough-In Drawing for Model VSB-400 Wiring Diagram for P300E/P400E, with 1 Batch Timer Wiring Diagram for P300E/P400E, with 2 Batch Timer Wiring Diagram for RAP300E/400E Wiring Diagram for Raps 300/400E Wiring Diagram #091-548 Wiring Diagram #091-182 Separate 120V Required for Controls 3 AMP LoadShuttle Brewers & Airpot/Shuttle Brewers Shuttle Brewers & Airpot/Shuttle Brewers Shuttle Brewers & Airpot/Shuttle Brewers Shuttle Brewer & Airpot/Shuttle Brewers Grindmaster Corporation

P300E, RAPS400E, P400E, RAP300E, RAP400E specifications

The Grindmaster RAP300E, RAP400E, P400E, RAPS400E, and RAPS300E are advanced coffee grinding machines designed for high-performance use in cafés, restaurants, and coffee shops. These models incorporate innovative technologies that cater to the increasing demand for efficiency and precision in coffee preparation.

Starting with the RAP300E, this grinder boasts an impressive grinding speed, ensuring that coffee enthusiasts can swiftly grind their favorite beans without sacrifice to flavor integrity. It features an intuitive display which allows for easy operation and adjustment of grind settings. The RAP300E utilizes durable burrs, enhancing its ability to maintain a consistent grind size, a critical factor for achieving the perfect espresso shot.

The RAP400E enhances the capabilities of the RAP300E with a stronger motor that accommodates larger volumes of coffee beans. This feature is particularly useful for businesses with high customer turnover. Additionally, this model includes advanced noise reduction technology, allowing for quieter operation—a significant advantage in busy coffee environments where the ambience matters.

The P400E makes its mark with a focus on portability and compact design. Ideal for smaller coffee shops or mobile setups, it retains the essential features found in larger models without compromising on quality. Users will appreciate its lightweight construction and easy-to-navigate interface, making it a standout choice for baristas on the go.

In the RAPS400E and RAPS300E models, Grindmaster introduces the innovative Automatic Portion System (APS), which ensures precise measurements for each coffee grind. This technology reduces wastage and ensures consistency in serving sizes, thereby maintaining the quality of each cup brewed. Both models offer extensive customization options for grind settings, enabling baristas to experiment with various brew methods.

Moreover, all these machines are built with user-friendly maintenance features. They offer easy access to the burrs for cleaning and adjustment, extending the lifespan of the equipment. The machines are also made from high-quality materials that ensure durability, crucial for demanding work environments.

In summary, the Grindmaster RAP series, along with the P400E, represents a leap in coffee grinding technology. These models are tailored to meet the evolving needs of the coffee industry, combining user-friendly designs with advanced functionalities, making them invaluable assets for coffee professionals.
Top Page Image Contents