Grindmaster P400ESHP instruction manual Drain Water Tank, Remove Brew Valve, Remove Heater

Page 11

Service (con't)

Drain Water Tank

Always empty the tank before shipping.

￿WARNING

Draining of tank should be performed by a qualified service technician. The tank contains very hot water. May cause severe burns.

Note: Brewer may contain over 5 gallons of hot water.

1)Prepare a heat resistant container to drain tank water into.

2)Shut off power to the brewer.

3)Remove the front access panel.

4)Pinch or clamp the silicone hose connected to fill valve.

5)Disconnect hose from outlet barb on fill valve.

6)Place hose over drain and release clamp.

7)Allow the tank to drain completely.

NOTE: It may be necessary to pinch the hose and stop the water before container is full. Carefully reinstall hose over fill valve outlet, then empty container. Repeat steps 4-7 completely to drain tank.

Remove Brew Valve

1)Disconnect electric power to machine.

2)Remove top cover and remove wires and small tube from valve.

3)Tilt inlet of valve down and pull sideways out of spray tee.

4)Clamp rubber tubing and disconnect valve from tubing.

Remove Heater

1)Disconnect power and remove top cover of brewer.

2)Disconnect wire leads to heater.

3)Remove tank cover by loosening retaining screw. Cover is lifted up with heater attached. Heater is then removed.

4)Replace heater with sealing washers in same configuration. When tightening nuts, hold element so it does not twist.

5)Replace tank cover ensuring O-ring seal is good.

6)Replace heater wires. Be sure all electrical connections are secure.

Shuttle Brewers & Airpot/Shuttle Brewers

Page 11

Image 11
Contents Shuttle Brewer & Airpot/Shuttle Brewers Shuttle Brewers & Airpot/Shuttle Brewers InstallationElectric Hook-up Start-upHot liquid in brew basket could cause burns Remove with care HOT Liquid Hazard OperationAdjusting the Timer AdjustmentsBrew Volume, Brew Timer Two Batch Timer with Knob Adjustment, See Figure Thermostat Adjustment To Adjust the BypassShuttle Brewers & Airpot/Shuttle Brewers Every Day CleaningAfter Each Brew Weekly or Bi-Weekly, Depending on Use ServiceRemove Heater Drain Water TankRemove Brew Valve Filling Problems Troubleshooting Filling, Heating, and BrewingRecovery time is Problem Possible Cause Service Check Remedy Brew volume too Description Parts Illustration for Models P300E & P400EParts Illustration for Model P400ESHP ABB1.5P Parts Illustration for Model RAP400EAABW-R Parts Illustration for Model RAPS400EParts Illustration for Model VSB-400 LID Stopper W/ O-RING Parts Illustration for Shuttle CS-LLRough-In Drawing for Model P-300 Rough-In Drawing for Model P-400 & P-400ESHP Rough-In Drawing for Model RAP-300 Rough-In Drawing for Model RAP-400 Rough-In Drawing for Model RAPS-300 Rough-In Drawing for Model RAPS-400 Rough-In Drawing for Model VSB-300 Rough-In Drawing for Model VSB-400 Wiring Diagram for P300E/P400E, with 1 Batch Timer Wiring Diagram for P300E/P400E, with 2 Batch Timer Wiring Diagram for RAP300E/400E Wiring Diagram for Raps 300/400E Wiring Diagram for P-400ESHP Wiring Diagram #091-548 For this Heat and Electric Service Wire PER FIG Wiring Diagram #091-182Grindmaster Corporation Form # AM-309-08 090-077

P400ESHP specifications

The Grindmaster P400ESHP is a top-of-the-line espresso machine designed for both efficiency and performance, catering to the needs of coffee professionals and enthusiasts alike. Its robust construction and innovative features make it a versatile choice for various establishments, from bustling coffee shops to high-end restaurants.

One of the primary features of the P400ESHP is its dual boiler system. This technology allows for simultaneous brewing and steaming, significantly reducing wait times during peak hours. The independent temperature control for each boiler ensures that each espresso shot is extracted under optimal conditions, enhancing the flavor and aroma profile of the coffee.

Additionally, the Grindmaster P400ESHP incorporates advanced PID temperature control. This precision technology ensures consistent temperature stability, which is crucial for producing high-quality espresso. The ability to adjust temperatures in real-time gives baristas the flexibility to experiment with different coffee beans and brewing methods, resulting in a bespoke coffee experience.

The P400ESHP is equipped with a user-friendly touchscreen interface that simplifies navigation through its various settings. Baristas can easily program drink recipes and access maintenance reminders, streamlining workflow and allowing for greater focus on quality beverage preparation.

Moreover, the machine features a powerful 20-bar pump that produces rich crema, enhancing the overall aesthetics and taste of the espresso. The high-performance steam wand is ergonomic, providing excellent control over frothing and texturing milk for lattes and cappuccinos. The wand’s ability to produce dry steam ensures that milk is heated quickly without excess moisture.

In terms of design, the Grindmaster P400ESHP boasts a sleek, stainless steel body that not only looks professional but also ensures durability in a busy environment. It is thoughtfully designed for easy access to internal components, facilitating straightforward maintenance and service.

The P400ESHP also focuses on energy efficiency, with an automatic shut-off feature that conserves power when the machine is not in use. This not only lowers operational costs but also aligns with environmentally-conscious practices.

In conclusion, the Grindmaster P400ESHP stands out as an advanced espresso machine that combines technology, efficiency, and user-centered design. Its outstanding features make it an ideal choice for coffee professionals seeking to elevate their beverage offerings while maintaining consistency and quality.