Grindmaster AMW B-Series manual Amw B-Series, Installation Start UP Procedure

Page 1

OPERATOR MANUAL

AMW B-SERIES

INSTALLATION

START UP PROCEDURE

WATER CONNECTION

The National Sanitation Foundation requires the following for an NSF approved water hook-up:

A quick disconnect water connection or enough coiled tubing so that the machine can be moved for cleaning underneath.

An approved backflow prevention device, such as a double check valve to be installed between the machine and water supply.

A 1/4” male flare adapter is provided. Installation to a water filter system is recommended to prevent lime and scale build-up in the machine.

Water pipe connections and fixtures directly connected to portable water supply shall be sized, installed and maintained in accordance with federal, state and local codes.

• Flush the water line to purge any debris from the supply line.

For 120V, 15A or 20A Service

Connect a 1/4” pressurized water line to the 1/4” male connection

(2 Wire + Ground)

 

 

(on rear of brewer) and turn the water supply on.

 

ON DUAL VOLT UNITS,

 

 

a) Minimum water pressure to the machine: 30 psi

 

FLIP SWITCH TO “120V”

b) Maximum water pressure to the machine: 80 psi

 

 

NOTE: Single head machines may be used without a pressurized water supply. (See Pour-Over Mode section)

ELECTRICAL CONNECTION

L1 N L2

CONNECT NEUTRAL (N) TO MIDDLE

CONNECT HOT (L1) TO LEFT SIDE

CONNECT GROUND TO SCREW

NOTE: Wiring connections should be performed by a qualified technician.

 

Figure A

(Refer to serial tag to verify model number of your machine)

For 120/208-240V, 20A Service

 

Remove front panel.

(3 Wire + Ground)

 

 

 

 

 

 

 

 

 

 

• Connect electrical service through rear of machine to terminal block

 

 

 

 

 

ON DUAL VOLT UNITS,

(inside front panel) marked L1, N, and L2. (See Figures A and B)

 

 

 

 

 

 

 

 

 

 

FLIP SWITCH TO “120V”

• On dual volt units, flip voltage switch (inside front panel next to terminal

 

 

 

 

 

 

 

 

 

 

block) to 120V for 120 Volt service or 240V for 120/208, or

 

L1 N L2

 

 

 

 

 

 

 

 

 

 

120/240 Volt service. (See Figures A, B and table below)

 

 

 

 

 

CONNECT HOT (L1) TO LEFT SIDE

 

Re-install front panel.

 

 

 

 

 

CONNECT GROUND TO SCREW

 

• Turn on (plug-in) electrical service to brewer.

 

 

 

 

 

CONNECT NEUTRAL (N) TO MIDDLE

 

 

 

 

 

 

CONNECT HOT (L2) TO RIGHT SIDE

• Water tank will fill after a 7-second delay. The machine will make a

 

 

 

 

 

 

Figure B

hissing sound when this occurs. On single head models, allow

 

 

 

 

 

 

 

 

 

 

 

approximately 1.5 minutes for the brewer to fill. On two head models, allow approximately five minutes for the brewer to fill.

NOTE: If water supply is inadequate or not connected, display will read “P-O” after 4 minutes of fill time (Refer to Pour-Over Mode section). If Fill Cycle times out and display reads “P-O” before tank is full, turn unit OFF then ON again to reset and continue filling.

The tank will begin heating slightly before machine fills.

Turn brewer on by pressing ON/OFF switch in front of machine. (Light will illuminate)

The brewer settings can be adjusted through the front touch pad. (Refer to Adjustments section)

The water will be hot and the brewer will be ready to brew when “READY” light illuminates.

Set Brew volume. (Refer to Setting Brew Volume section)

POWER REQUIREMENTS: (Refer to serial tag for voltage to be supplied.)

Applied Volts

Models

Watts

Amps

NEMA Plug

Cord AWG

Connections

 

 

 

 

 

 

 

 

B-3, B-3WL, B-3WR

1800

15

 

 

Hot to L1

120

 

 

 

5-15P, 5-20P for CUL

3X14

Neutral to N

B-SAP, B-ID

1780

14.9

 

 

 

Ground to ground screw

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B-3, B-3WL, B-3WR

2920

14.1

L14-20P

4X12

Hot to L1

 

 

 

 

 

B-SAP, B-ID, B-DAP, B-DGP

2620

12.6

 

Neutral to N

120/208

 

 

 

 

 

 

 

Hot to L2

B-6

5110

24.6

L14-30P

4X10

 

 

 

 

 

Ground to ground screw

 

B-DAP, B-DGP (30A)

4510

21.7

 

 

 

 

 

 

 

 

 

 

 

 

B-3, B-3WL, B-3WR

3800

15.9

L14-20P

4X12

Hot to L1

 

 

 

 

120/240

B-SAP, B-ID, B-DAP, B-DGP

3500

14.6

Neutral to N

 

 

B-6

6600

27.5

L14-30P

4X10

Hot to L2

 

 

 

 

 

Ground to ground screw

 

B-DAP, B-DGP (30A)

6000

25

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 1
Contents AMW B-SERIES Installation Start UP ProcedureSeries AdjustmentsBrewing Procedure Setting Brew VolumePulse Brewing Mode Energy Savings Mode Warmer SHUT-OFFPOUR-OVER Mode LOW TEMP/NO Brew ModeCleaning Cabinet Cleaning WarmersUser Lockout Programming for B-Series Models B-3, B-3WR, B-3WL, B-SAP & B-ID Parts List Serial numbers A166226P and higher with a -P suffix 3WL Models B-6, B-DGP & B-DAP Parts List Serial numbers A166226P and higher with a -P suffix A61243 Grommet Dump Valve A71684 Touch Pad w/ Cable Problem Possible Cause Solution Troubleshooting GuideWiring Diagram Wiring Diagram Models B-6, B-DAP, B-DGP Wiring Diagram E Models Models B-3, B-3WR, B-3WL, B-SAP & B-ID Wiring Diagram Models B-6, B-DAP, & B-DGP Wiring Diagram E Models Page Page Box 35020 Louisville, KY 40232 USA

AMW B-Series specifications

The Grindmaster AMW B-Series is a premium line of commercial coffee grinders that has gained popularity among coffee aficionados and café owners alike. Renowned for its exceptional performance, durability, and user-friendly features, this series is designed to meet the demanding needs of high-volume coffee environments.

One of the standout features of the AMW B-Series is its advanced grinding technology. Equipped with precise, high-quality burrs, the grinders ensure a consistent particle size, which is crucial for extracting the finest flavors from coffee beans. This consistency minimizes the variations in taste and aroma that can occur with less sophisticated grinding methods, enabling baristas to offer a superior cup of coffee every time.

The B-Series also boasts a user-friendly interface, with an easy-to-read digital display that simplifies operation. Baristas can easily adjust grind settings, while pre-programmed grind times allow for quick changes between different types of coffee. This versatility is essential for busy cafés that serve a range of coffee drinks, from espresso to French press.

Built to withstand the rigors of daily use, the AMW B-Series features a robust construction that guarantees durability. The materials used in the grinder's design are of the highest quality, ensuring that it can handle the continuous demands of a bustling coffee shop without compromising performance. Additionally, the compact design makes the grinders easy to fit into various kitchen spaces, even in establishments where counter space is at a premium.

Another notable characteristic of the B-Series is its relatively low noise operation compared to other grinders in its class. This feature is particularly appreciated in café environments where a tranquil atmosphere enhances the customer experience. With a focus on energy efficiency, the grinders are designed to consume minimal power, contributing to a more sustainable coffee operation.

Furthermore, the Grindmaster AMW B-Series incorporates innovative safety features that provide peace of mind for operators. The grinders are equipped with automatic shut-off capabilities, reducing the risk of overheating and potential damage to the machine.

Overall, the Grindmaster AMW B-Series combines advanced technology, ease of use, and robust construction to create a top-tier coffee grinding solution. Ideal for any commercial setting, these grinders uphold the quality and consistency needed to produce exceptional coffee every day.