Graco 1466 Operating the Six-Speed Swing, To Turn Off the Swing, Using the Timer, To Use Music

Page 7

Operating the Six-Speed Swing

Your swing has six speed settings. The “LOW” button controls the three low-range speeds and the “HIGH” button controls the three high-range speeds.

The lights indicate what speed is activated. The green lights indicate the three low range speeds and the red lights indicate the three high range speeds. For exam- ple, if the far right light is green, speed 3 is activated.

 

 

Indicator lights

 

 

 

 

 

 

 

 

 

 

 

 

 

HIGH button

 

 

 

 

 

 

 

 

 

 

LOW button

 

 

 

 

 

 

 

 

 

controls three

controls three

 

 

 

 

 

 

 

 

 

high-range

low-range

 

 

 

 

 

 

 

 

 

 

speeds

 

 

 

 

 

 

 

 

 

 

speeds

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MUSIC button

TIMER button

 

sets swing time

 

turns music on

 

in ten-minute

 

and controls

 

increments

 

volume

 

 

 

Push the LOW button once for speed 1, twice for speed 2 or three times for speed 3.

Push the HIGH button once for speed 4, twice for speed 5 or three times for speed 6.

To go from speed 2 to speed 3, just push the LOW button once.

It is not necessary to start at lowest speed and move up. The swing can begin directly at speed 5, for example, by pushing the HIGH button two times. Or it can go from speed 6 to speed 2 by pushing the LOW button twice.

After choosing speed, start swing by giving it a gentle push. Observe swinging motion for a minute. It takes time for the swing to adjust to a setting. Change setting as needed.

Your seat may be stopped at any time the motor is running without damaging the motor. Push swing to restart.

If your swing motor stops operating by itself, a protective device may have been activated. Turn off motor, wait three minutes, then restart swing.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation. This equipment generates, uses and can radiate frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

!Reorient or relocate the receiving antenna.

!Increase the separation between the equipment and receiver.

!Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

!Consult the dealer or an experienced radio/TV technician for help.

152-12-99 IS2481

13

To Turn Off the Swing

Press and hold either speed button. Indicator light will go off and swing will stop.

Using the Timer

You can program your swing to turn off after a certain period of time. The timer button, located between the two speed buttons, sets the swing time in ten-minute increments up to 40 minutes. Push the button once; the swing will run for ten minutes.

To add time, push the timer button once more for every ten minutes you wish to add. The active speed setting light will blink in repetition, one blink for every ten minutes programmed. The number of blinks will decrease to give you an indication of the time remaining.

The light will blink continuously when a minute or less of time is remaining. If you do not set the timer at all, your swing will run until you turn it off. To cancel timer mode, press and hold the timer button until the light stops blinking.

If you are using the timer, both the swing and the music will stop when the time runs out.

For example, if the center light is red and it’s blinking two times quickly between pauses, your swing is on speed 5 and will run for twenty minutes before stopping.

To add time, push the time button once or twice.

To turn swing off, press and hold either speed button briefly.

To Use Music

If you want music for your baby, push the music button until desired volume is reached:

Push once for high volume.

Push a second time for

* medium volume.

Push a third time for low * volume.

Push a fourth time to turn * music off.

The music control is independent of the speed and timer settings. You can have any combination of speed, timer and music settings.

14

Image 7
Contents Congratulations on your purchase of a Graco swing Model NosCustomer Satisfaction Failure to follow these warnings could result in seriouAtion Hazard Gs and the assembly instructions rious injury or deathStep Attaching the LegsAttaching the Base Tubes Attaching the FeetAttaching the Back Brace Attaching the Hanger Tubes and SeatAttaching the Tray Attaching the Seat Belt To Install CoversMix ’N Move Toy System To Remove CoversReclining Back Four Positions Installing the BatteriesUsing the Tray Using the SwingTo Use Music Using the TimerOperating the Six-Speed Swing To Turn Off the SwingInstructions for ordering swing parts Caring for Your Battery Powered SwingReplacement Parts Parts List

1466 specifications

The Graco 1466 is a powerful and versatile airless paint sprayer designed for both professionals and DIY enthusiasts looking for efficiency and high-quality results in their painting projects. Known for its robust performance, the Graco 1466 stands out in the market with several notable features, cutting-edge technologies, and characteristics that make it a preferred choice among users.

One of the key features of the Graco 1466 is its powerful motor, which provides the necessary pressure to spray a variety of coatings, including paints, stains, and sealers. This strength allows the user to tackle various surfaces, from walls and fences to decks and furniture, making it suitable for both interior and exterior applications. The unit is equipped with a 5/8 HP motor, delivering an impressive output that allows for efficient project completion with minimal effort.

The Graco 1466 also includes a flexible suction hose that allows for easy paint pickup from a 1 or 5-gallon container, offering the convenience of working with different sized paint containers without limitations. In addition, the unit features an adjustable pressure control knob, enabling users to customize the flow rate according to their specific painting requirements. This feature ensures that the user can achieve a smooth and even finish, reducing the risk of drips and overspray.

Ergonomically designed, the Graco 1466 is lightweight and portable, making it easy to move around the job site. It features a robust frame, ensuring durability and stability during operation, coupled with a convenient carry handle that enhances mobility. The paint sprayer is equipped with a reversible spray tip, which allows for quick unclogging during operation, thus minimizing downtime and improving overall productivity.

Another significant aspect of the Graco 1466 is its ease of cleaning and maintenance. The unit features a simple flush system that makes the cleaning process straightforward after use, which is essential for maintaining the sprayer's longevity. Users can flush the system with water or solvent, depending on the type of paint used, ensuring that it remains in optimal working condition for future projects.

In summary, the Graco 1466 combines powerful performance, user-friendly features, and cutting-edge technologies to provide an exceptional painting experience. Its versatility, adjustable pressure control, lightweight design, and easy maintenance reflect Graco’s commitment to quality and innovation in the painting industry, making the Graco 1466 a dependable choice for any painting endeavor.