Fishman Aura manual Suggestions for Mixes

Page 28

Acoustic Imaging Blender Aura™

Adjust the EQ

Move the Parameter knob to Bass, Mid or Treble for either the Aura or Pickup and adjust to taste with the Data knob. For best results, apply EQ to the “Aura” side (Sound Image) sparingly. You can apply EQ more liberally for the pickup side. Typically you boost Bass and Treble a bit and cut Mid for the pickup. After you apply EQ, go back to Blend and double-check the balance between the pickup and the Aura (Sound Image).

Set the Compressor (optional)

If you want a bit more punch and sustain from your sound, move the Parameter knob to Compressor and turn the Data knob clockwise.

For strumming, set the compressor to about C1 or C2. For single note leads and fingerstyle, turn the Data knob clockwise past C9 to L1 or L2.

Check the Level

Turn the Parameter knob to Level and check the overall volume of your mix by pushing the Effect On/Off switch several times. Use the Data knob to match the level of the mix to the dry, unadorned pickup sound.

Set Feedback Cancel

Once you have all your parameters adjusted, raise the Output level and see if the instrument will feedback. If it does, lower the Output Level, then hold down the Feedback Cancel footswitch for over two seconds until the LED over the switch flashes. Raise the output level until the feedback returns and it will be recognized by the Feedback Cancel circuit and eliminated.

Finish Up

Now that you have set up all the parameters, move the Edit/Play switch back to Play and you are done. Remember that the location of any mix you create will always get assigned to the last selected program location. Go make some music!

Suggestions for Mixes

Rhythm Guitar

Cut mids for both the Aura (Sound Image) and the pickup EQ. Try adding a little bit of “C” compression (C1 or C2) to fill out the chords.

Flatpicking

Blend in a bit more Sound Image than pickup (about 5 or 6 in the display) and cut the treble for the Aura (Sound Image).

Fingerstyle

Set Blend to 3 or 4 and boost bass slightly for the Aura (Sound Image). Boost bass and treble and cut the mids for the pickup. Use a little bit of “L” Compression (L1 or L2) for more “snap”.

Nylon String

Classical guitars tend to have a very open bass response, so cut bass for the Aura (Sound Image).

Solo (boost) setting

If you need more level for a solo section in a piece, go to the level parameter and boost as required.

Mute setting

You can effectively mute any program location you choose.

1Go to Play mode and select the program location you wish to mute.

2Go to Edit mode and set the Select parameter to “oF”.

3Set the Blend parameter to 4.

4Go to the Phase parameter and toggle the Data knob back and forth. Leave the Data knob in the position that mutes the sound.

5Return to Play mode.

Recording

For recording, set the Blend parameter to 7 or A.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Acoustic Imaging Blender Aura Acoustic Imaging Blender Aura Table of Contents Get Your Feet Wet Jump In the Deep EndWelcome What Is a Sound Image?Please fill out the Product Registration form online at Aura Capabilities What does it do?What you can expect from the Aura? Size MattersMidi Requirements Aura, the Internet and YouAura Custom Shop Rear Panel Front Panel Chapter Five Basic Control Groups Feedback Cancel seeInput/Output see Factory Default Settings LED DisplayEffect on/off Switch Edit/Play SwitchData Knob Inner Workings Phase Switches Why a Global Phase Switch?Input /Output Input Level and LEDsPlay Mode How to use the Phase switchesEdit/Play Switch Why a Phase Switch on the Parameter Knob?Resetting the Aura to Factory Specs Pre-select Change ModeEffect on/off Switch Setup Edit ModeData Knob Guidelines for Selecting a Sound Image Parameter KnobSelect We recommend sizing a Sound Image to fit your instrumentBlend Aura EqualizationPickup Equalization Phase Switches Compressor LevelCompression Chords and Rhythm Compression Lead, Flatpicking and Finger styleTuner Tuner SetupMute Defeat Feedback Cancel Factory Default Feedback CancelOn the Fly Feedback Cancel Play Mode Programmable Feedback Cancel Edit ModeSetting Up for Performance Setting Up for Performance Understanding Aura NavigationSetting Up a Mix Suggestions for Mixes Build Your Own Programs for Performance Specifications BoostGlossary Troubleshooting Factory Default Settings Factory DefaultsPrograms 17 through Pickup appears in the Aura channelPlay Mode Factory Sound Image/Pickup MixesPrograms Limited Warranty To obtain factory service

Aura specifications

The Fishman Aura is a cutting-edge acoustic imaging system that revolutionizes the way musicians connect with their instruments. Designed to enhance the acoustic guitar experience, it offers an unparalleled level of sound quality and tonal versatility.

At the heart of the Fishman Aura is its unique technology, which employs advanced imaging techniques to capture the true sound characteristics of a guitar. This system allows players to achieve studio-quality sound without the need for complex microphone setups. The Aura features a selection of pre-amped images that replicate the tonal attributes of various high-end acoustic guitars, ensuring that musicians can find the perfect sound for their playing style and genre.

One of the standout features of the Fishman Aura is its easy-to-use interface. With its intuitive controls, musicians can quickly select between numerous guitar images, adjusting their tone to fit the context of their performance. This flexibility is particularly beneficial for singer-songwriters or performers who switch between different instruments, as it allows for swift and seamless transitions.

In addition to its imaging capabilities, the Fishman Aura incorporates high-quality preamp technology. This ensures that the signal output is not only clean and clear but also rich in dynamics, making it suitable for both live performances and studio recordings. The preamp is specifically designed to minimize feedback, a common challenge when amplifying acoustic instruments.

Another notable characteristic of the Fishman Aura is its compatibility with a variety of pickup systems. Whether you have a traditional piezo pickup or a more modern under-saddle sensor, the Aura can easily accommodate your setup. This universal compatibility further extends the versatility of the system, making it an excellent choice for any guitarist seeking to enhance their sound.

Durability is also a key consideration in the design of the Fishman Aura. Built to withstand the rigors of road use, it features a robust construction that ensures reliability in diverse performance environments. Its compact form factor makes it easy to transport, allowing musicians to take their sound anywhere.

In summary, the Fishman Aura is an innovative acoustic imaging system that elevates the performance of acoustic guitars. With its unique sound imaging technology, user-friendly controls, high-quality preamp, compatibility with various pickups, and durable design, it stands out as an essential tool for both live and studio applications. Whether you're a seasoned professional or an aspiring musician, the Fishman Aura is sure to enhance your acoustic sound experience.
Top Page Image Contents