Thermax CP3 manual System Clean-Up, General System Maintenance

Page 7

System Clean-Up

When the carpet cleaning process is complete, it’s time to clean the system. De-activate all switches to “OFF” position.

1)Empty and rinse recovery tank.

2)Empty solution tank.

a.To empty solution tank of unused solution, turn vacuum switch to “ON” position.

b.With vacuum hose still connected to the inlet and vacuum running, drop the end of the vacuum hose (opposite the end plugged into the vacuum inlet) down through the solution tank fill hole (page 3, #2) and SLOWLY remove the unused solution from

the solution tank until empty. The system will transfer the solution to the recovery waste tank for disposal. In the process, the solution cleans out the inside of the vacuum hose.

NOTE: Take caution to remove the solution SLOWLY! Make sure to rinse solution tank with the plain hot water to minimize chemical build-up. After rinsing solution tank, transfer rinse water in the same manner mentioned above.

c. Deactivate and unplug the system

d. Empty the recovery tank and clean.

e. Remove vacuum and solution hose from system. Wipe down all exterior areas of the system.

3) Your CP3 system is now ready for storage until the next job!

General System Maintenance

Daily (At the conclusion of each work day)

1)Empty, rinse and clean solution and recovery tanks with plain hot water thoroughly cleaning dirt and obstructions from inside the tanks.

2)Clean vacuum and solution hoses thoroughly.

3)Run plain hot water through solution tank and pump to prevent any chemical build-up.

4)Wipe down all exterior surfaces with an all-purpose type cleaner, then apply a light coat of vinyl protectant to all exterior surfaces.

5)Lubricate couplings, hinges and wheels with silicone-type spray.

6)Inspect the solution tank filter and recovery tank dome filter for hair and debris. The filter should always be kept clean and unobstructed.

7)Inspect electrical cord for damage or fraying and repair as necessary.

8)Store unit away from direct sunlight and freezing temperature.

MONTHLY

1)Inspect internally for:

a.Loose nuts and/or screws

b.Leaking hoses

c.Loose wiring

d.Anything that doesn’t appear correct

2)Flush the system with 2 cups white vinegar per gallon of hot water solution. Follow by circulating plain hot water through the system via the solution tank. This helps reduce and neutralize any alkalai and chemical build-up.

NOTE: To prevent shock hazard, remember to unplug main power source before inspection or repair of the system.

ANNUALLY

We recommend that your system be inspected once a year by an authorized Thermax service technician. For the location of your nearest Service Center, call 1-888-764-3700 or go to thermaxaf.com.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents CP3 Table of Contents Message from the Corporate Office Identifying Features Inspection Upon Delivery Important Safety InformationExtraction Cleaning Procedure Set-Up ProcedureGeneral System Maintenance System Clean-UpOptional Packages & Accessories Optional Accessories World’s Liquid Carpet & Upholstery Steam Cleaning Solutions Air Purifiers and SolutionsThermax CP3 Wiring Diagram Thermax CP3 SpecificationsTroubleshooting Condition Cause Correction Thermax CP3 Schematic GASKET, DOME, CP3/CP12 Thermax CP3 Parts ListFloor Wand Schematic Item no Thermax no Description Floor Wand Parts ListUpholstery Wand Schematic Upholstery Wand PArts list Power Brush Schematic PLATE, WEAR, STMHD, PB309 Power Brush Parts ListAdditional Commercial Units CP3 Warranty 06-312-02 4/07

CP3 specifications

Thermax CP3 is an advanced cooling solution designed for various industrial and commercial applications. Known for its energy efficiency and innovative features, the Thermax CP3 stands out as a reliable choice for businesses seeking sustainable temperature control.

One of the main features of the Thermax CP3 is its use of advanced refrigerant technology. The system employs eco-friendly refrigerants that minimize environmental impact while ensuring optimal cooling performance. This commitment to sustainability is further enhanced by the system’s energy-efficient design, which significantly reduces electricity consumption compared to traditional cooling systems.

The CP3 features a robust scroll compressor that enhances reliability and longevity, providing consistent performance even under varying load conditions. This compressor technology is pivotal in ensuring reduced operational noise, making the CP3 ideal for settings where low noise levels are essential.

Another significant characteristic of the Thermax CP3 is its modular design. This allows for easy installation and maintenance, ensuring that companies can adapt the cooling systems to suit their specific needs swiftly. The modular setup also facilitates scalability, enabling businesses to expand their cooling capacity without the need for extensive redesign or infrastructure changes.

The Thermax CP3 also incorporates smart technology for enhanced operational efficiency. It features an advanced control system that monitors various parameters, allowing for real-time adjustments to optimize performance. This intelligent system helps in detecting anomalies, leading to better predictive maintenance and reduced downtime.

Additionally, the CP3 is designed to operate under harsh environmental conditions. Its rugged construction ensures durability, while its corrosion-resistant materials extend the lifespan of the unit. This makes it suitable for use in various industries, including pharmaceuticals, food processing, and chemical manufacturing, where temperature control is critical.

Furthermore, the unit’s low footprint makes it an attractive option for urban settings where space is a premium. The CP3 offers high cooling capacity without occupying substantial ground area, making it ideal for businesses looking to maximize their operational space.

In summary, Thermax CP3 is not just an ordinary cooling solution; it embodies the future of sustainable cooling technology, combining energy efficiency, modularity, intelligent controls, and robust construction into a single package. This positions it as a preferred choice for industries aiming for both performance and sustainability in their operations.
Top Page Image Contents