Thermax CP3 manual Set-Up Procedure, Extraction Cleaning Procedure

Page 6

Set-Up Procedure

1)Pre-mix cleaning solution as required for specific application in a five gallon (19 liter) pail. Pour pre-mixed solution through solution fill hole of system (page 3, #2).

NOTE: This system has a built-in solution heat maintenance feature, start with hot water if possible. Hot water is hygienic and maximizes cleaning potential.

2)Add appropriate amount of defoamer to the recovery tank (page 3, #3).

3)Connect end of the vacuum hose to the vacuum inlet connector (page 3, #8).

4)Connect male end of the solution hose to female quick-connect coupling (page 3, #6), and female end of solution hose to the male end of the cleaning wand.

5)With solution tank full and vacuum and solution hoses properly connected, plug main power cord (page 3, #5) into properly grounded outlet.

NOTE: Plug the cord into an outlet that will be out of the way of the cleaning path, ideally a 20 amp circuit when available.

6)Your system is now ready for operation.

7)Once pre-spray, furniture removal and other carpet preparation is complete, proceed to clean carpet and/or upholstery. NOTE: Vacuum and pump switches can now be activated to “ON” position.

Extraction Cleaning Procedure

1)With solution tank full and all hoses appropriately attached, activate pump switch to the “ON” position, then activate the vacuum switch to the “ON” position.

2)Start in area of the room opposite from where you want to end.

3)Place wand about 4 feet in front of you.

4)Activate the solution spray trigger of wand.

5)Laying down an even spray of solution, pull the wand back towards you slowly.

6)Release the solution spray trigger and move the wand slowly forward over the same area just cleaned to recover additional solution left behind. Repeat this process several times depending on the degree of carpet soiling then move over the width of the wand, overlapping slightly to prevent streaking. For best results, work in approximately 4 foot wide sections and always be sure to remove as much solution from the carpet as possible as this will minimize drying time.

7)When solution tank is empty and needs refilling, shut system down and repeat step 1 of “Set Up Procedure”.

8)Remove, empty and replace recovery holding tank. (page 3, #3).

NOTE: Always empty and replace recovery tank at the same time you refill the solution tank.

9)Add more defoamer into the recovery holding tank (step 2 of “Set Up Procedure”).

NOTE: With solution tank full and recovery tank empty, the system is now ready to continue cleaning. Continue the process until cleaning is complete.

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents CP3 Table of Contents Message from the Corporate Office Identifying Features Important Safety Information Inspection Upon DeliverySet-Up Procedure Extraction Cleaning ProcedureSystem Clean-Up General System MaintenanceOptional Packages & Accessories Optional Accessories World’s Steam Cleaning Solutions Air Purifiers and Solutions Liquid Carpet & UpholsteryThermax CP3 Specifications Thermax CP3 Wiring DiagramTroubleshooting Condition Cause Correction Thermax CP3 Schematic Thermax CP3 Parts List GASKET, DOME, CP3/CP12Floor Wand Schematic Floor Wand Parts List Item no Thermax no DescriptionUpholstery Wand Schematic Upholstery Wand PArts list Power Brush Schematic Power Brush Parts List PLATE, WEAR, STMHD, PB309Additional Commercial Units CP3 Warranty 06-312-02 4/07

CP3 specifications

Thermax CP3 is an advanced cooling solution designed for various industrial and commercial applications. Known for its energy efficiency and innovative features, the Thermax CP3 stands out as a reliable choice for businesses seeking sustainable temperature control.

One of the main features of the Thermax CP3 is its use of advanced refrigerant technology. The system employs eco-friendly refrigerants that minimize environmental impact while ensuring optimal cooling performance. This commitment to sustainability is further enhanced by the system’s energy-efficient design, which significantly reduces electricity consumption compared to traditional cooling systems.

The CP3 features a robust scroll compressor that enhances reliability and longevity, providing consistent performance even under varying load conditions. This compressor technology is pivotal in ensuring reduced operational noise, making the CP3 ideal for settings where low noise levels are essential.

Another significant characteristic of the Thermax CP3 is its modular design. This allows for easy installation and maintenance, ensuring that companies can adapt the cooling systems to suit their specific needs swiftly. The modular setup also facilitates scalability, enabling businesses to expand their cooling capacity without the need for extensive redesign or infrastructure changes.

The Thermax CP3 also incorporates smart technology for enhanced operational efficiency. It features an advanced control system that monitors various parameters, allowing for real-time adjustments to optimize performance. This intelligent system helps in detecting anomalies, leading to better predictive maintenance and reduced downtime.

Additionally, the CP3 is designed to operate under harsh environmental conditions. Its rugged construction ensures durability, while its corrosion-resistant materials extend the lifespan of the unit. This makes it suitable for use in various industries, including pharmaceuticals, food processing, and chemical manufacturing, where temperature control is critical.

Furthermore, the unit’s low footprint makes it an attractive option for urban settings where space is a premium. The CP3 offers high cooling capacity without occupying substantial ground area, making it ideal for businesses looking to maximize their operational space.

In summary, Thermax CP3 is not just an ordinary cooling solution; it embodies the future of sustainable cooling technology, combining energy efficiency, modularity, intelligent controls, and robust construction into a single package. This positions it as a preferred choice for industries aiming for both performance and sustainability in their operations.
Top Page Image Contents