•ALL RANGES CAN TIP
•INJURY COULD RESULT
•INSTALL
•SEE INSTALLATION INSTRUCTIONS
|
| STABILITY | DEVICE | INSTALLATION | INSTRUCTIONS |
|
|
|
| |||||||
|
|
|
|
|
| FOR BRACKET | KIT NO. 342473 |
|
|
|
|
| ||||
TOOLS NEEDED: |
| Phillips head screwdriver |
|
|
|
|
|
|
|
| ||||||
|
|
| 1 3/8" open end or adjustable wrench |
|
|
|
|
|
|
| ||||||
Bracket attachesto | floor or wallto | hold either right or left | 3. | Determine whet her you will anchor t he bracket to the | ||||||||||||
rear leg leveler. If fastening | to floor, be sure that screws |
| floor or wall. Fasten the bracket securely | with the | ||||||||||||
do not penetrate | electrical | wiring or plumbing. If this |
| screws | provided. | Screws are | In wood, | |||||||||
cannot be determined, | use shorter screws that will not |
| plywood, particle | and chip | board, | and most metal | ||||||||||
penetrate through | flooring. |
|
|
|
|
| framing. Ifattachlngtomasonry, | youcanbuysultable | ||||||||
If the bracket came with your range, It is shipped at- |
| screws | and anchors at hardware | stores. Use a | ||||||||||||
tached to the lower range back. | Remove and discard |
| masonry drill to drill the required holes. |
| ||||||||||||
the shipping screw that holds the bracket and then | 4. | Using the wrench, | back out the four leg levelers at | |||||||||||||
follow Instructions | below. |
|
|
|
| |||||||||||
|
|
|
|
| least two turns. See your installation guide for more | |||||||||||
1. Decide whether the bracket will be installed on the |
| |||||||||||||||
| leveling information before | positioning range. | ||||||||||||||
right or left side of range location. |
|
| ||||||||||||||
| 5, | Slide the range into place. | Be sure rear leg leveler | |||||||||||||
2. If the bracket side of the range is adjacent to a | ||||||||||||||||
| fully engages slot in bracket. | If range cannot be | ||||||||||||||
cabinet, | place | the | bracket | against back | wall and |
| moved | back far enough for rear leg leveler to enter | ||||||||
cabinet as shown | in Figure | 1. |
|
|
| bracket, move bracket forward as required and attach | ||||||||||
If there is no adjacent cabinet, determine where the |
| to floor in new location. |
|
|
|
| ||||||||||
|
|
|
|
|
|
|
| |||||||||
location of the range side (painted outside panel) will |
|
|
|
|
|
|
|
| ||||||||
be. Place the bracket with its outside edge at this |
|
|
|
|
|
|
|
| ||||||||
location and against back wall. See Figure 1. |
|
|
|
|
|
|
|
| ||||||||
ADJACENT | CABINET OR FINAL |
|
|
|
|
|
| BRACKET |
|
| WALL | |||||
LOCATION | OF RANGE | SIDE |
|
| OUTSIDE | EDGE OF |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| PLATE | ||||||||
PANEL |
|
|
|
|
| BRACKET | TO BE |
|
|
|
|
|
| |||
|
|
|
|
|
| SCREWMUST ENTER_ |
|
| / |
| ||||||
|
|
|
|
|
| FLUSH WITH LEFT OR |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| WOOD OR METAL |
|
|
|
| |||||
|
|
|
|
|
| RIGHT SIDE OF RANGE |
|
|
|
|
| |||||
|
|
|
|
|
|
| \ |
|
|
| / |
|
|
|
|
WALL BEHIND •
RANGE
"_=_". ""r_._ _
ATTACHMENT TO WALL
Fig, 1 | Fig. 2 |
1 |