Sears 790.93752, 790.93754, 790.93751 Before Setting Oven Controls, Setting Surface Controls

Page 7

Before Setting Oven Controls

OVEN VENT LOCATED

UNDER LEFT REAR ELEMENT

Oven Vent Location

For models equipped with coiled surface elements, the oven vent is located under the left rear surface element. When the oven is on, warm air flows through the left rear element. This venting is necessary for proper air circulation in the oven and good baking results. DO NOT BLOCK THE OVEN VENT.

Arranging Oven Racks

ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO

OPERATING THE OVEN). Always use oven mitts when using the oven.

Removing & Replacing Oven Racks

To remove, pull the rack forward until it stops. Lift up front of rack and slide out. To replace, fit the rack onto the guides on the oven walls. Tilt the front of the rack upward and slide the rack back into place.

Rack

RECOMMENDED

RACK POSITIONS

FOR

 

BROILING,

BAKING & ROASTING

 

 

Food

 

Rack Position

 

Broiling meats, chicken or fish

1,2 or 3

 

Cookies, cakes, pies, biscuits & muffins

3 or 4

 

Frozen pies, angel food cake, yeast, bread,

5

 

casseroles, small cuts of meat or poultry

 

 

Turkey, roast or ham

 

Roasting shelf

Roasting

Shelf (some models)

LO

1

Setting Surface Controls

To Operate the Surface Elements:

1.Place cooking utensil on the surface element.

2.Push in and turn the surface control knob in either direction to the desired setting. Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. The control knobs do not have to be set exactly

on a particular setting. Use the settings as a guide and adjust the control knob as needed.

9

3.When cooking is completed, turn the surface element off before removing the

8pan. Note: The surface "Element On" indicator light(s) will glow when one or more elements are turned on. A quick glance at these indicator light(s) when

cooking is finished is an easy check to be su re all surface elements are turned off.

Note: See page 8 for suggested surface control settings for different types of food.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the range when it is in use.

These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.

7

Image 7
Contents Manual del Usuario Estufa ElectricaSears Maintenance Agreement Full ONE Year Warranty on ALL PartsWE Service What WE Sell Sears Maintenance AgreementsImportant Safety Instructions Important Instructions for Cleaning Your Range Important Instructions for Using Your CooktopImportant Instructions for Using Your Self Cleaning OvensSerial Plate Location Important Safety NoticeSimmerSelect Range FeaturesSetting Surface Controls Before Setting Oven ControlsSimmerselect To Operate Simmer Select Surface Element If equippedConversion Oven Control FunctionsTo Change the Minute Timer while it is in use Setting Oven ControlsTo Set Control for Continuous Bake or 12 Hour Energy Saving To Set or Change the Temperature for BakingTo Program Oven for a Delayed To Set the Timed Bake FeatureWhen the Set Bake Time Runs Out Rack Position From Top Food To BroilTo Operate the Warmer Warm & Ready TM Drawer Setting Warmer Drawer ControlsTo Remove Warmer Drawer Turn power off before removing the warmer drawerRemoving Replacing Warmer Drawer If equipped To Remove and Replace Warmer Warm & Ready TM DrawerSelf-Cleaning Oven Self-CleaningAdhere to the following cleaning precautions When the Self-Clean Cycle is Completed To Start the Self-Clean CycleStopping or Interrupting a Self-Cleaning Cycle To Set the Controls for a Self-Clean CycleSurfaces How to Clean Care & CleaningIiill ii i!!i To Remove Oven Door Adjusting Your Oven TemperatureTo Adjust Oven Temperature To Remove and Replace Oven DoorBefore You Call Possible CAUSE/SOLUTIONOccurrence Possible CAUSE/SOLUTIONPage LE-FOYER ic A. and CanadaPART6 a.m. 11 p.m. CST, 7 days a week A. only P.m. Sat