Russound In-Ceiling speaker owner manual When Pre-Construction or Retrofit Installation

Page 8

WHEN – Pre-Construction or Retrofit Installation

WHEN - PRE-CONSTRUCTION OR RETROFIT INSTALLATION

PRE-CONSTRUCTION INSTALLATION Built-in speaker installation is more convenient during home construction than after construction is completed. Speaker wire can be routed to the destination before the wallboard is installed, and possible hindrances such as AC wiring, plumbing, or ductwork can be easily located and avoided.

Speaker rough-in brackets are used in the pre-construction phase of speaker installation during construction of new homes and additions. Russound offers Speaker Rough-In Brackets for the full line of Advantage speakers. These brackets are designed to provide drywall installers the cor- rect cut-out pattern for the speakers. The brackets have “wings” that are nailed/screwed/stapled onto the ceiling studs. Once the wallboard is installed, the opening is cut out and the speaker frame is inserted into the bracket.

When installing the pre-construction bracket, note that there are holes molded into the bracket for speaker wire tie-off. This keeps the wire from getting lost later during the construction process. You can also tie the wire to the bezel/mounting assembly once it’s installed, using any of the rotating clamp towers.

DURING NEW INSTALLATION, KEEP THE FOLLOWING TIPS IN MIND:

•Use a small level to verify that the rough-in bracket is straight.

•If possible, run speaker wires after AC wiring is in place to avoid induced hum caused by close parallel proximity of the two types of wire.

•If possible, run speaker wires after plumbing is in place; wire can bend, pipes cannot.

•Secure speaker wires in place against a stud along vertical runs with insulated staples only, being careful not to pierce the wire insulation. Allow a bit of slack for expansion of building materials.

•Horizontal runs should be routed through holes drilled in studs at roughly equal heights.

•The actual speakers should not be installed until the wallboard is in place. In the meantime, leave several feet of wire coiled up and secured to the back side of

Figure 2 New construction use of Rough-in Bracket

Not for use with Retrofit applications

the mounting frame. Excess length can be removed during final assembly.

•Any speaker installed in a ceiling should have a safety wire firmly tied between the back of the speaker assem- bly and the frame of the building. There is a marked location provided for this purpose on the back of all Advantage Twist & Tilt speakers. Use any strong insulat- ed wire and connect it to the speaker being careful not to let it interfere with the speaker’s operation. The other end should be firmly attached to the studs or flooring above using a hook, nail, or other reliable fastener.

•When installing the drywall, make sure the speaker cut-out hole doesn’t extend farther than 1/4” from the inside of the mounting frame. The flat rough-in brackets and wings are thin enough that they won’t interfere with wallboard installation.

•After the wallboard is secured, install the speakers as described in the installation instructions in this manual.

RETROFIT INSTALLATION

If you are installing Russound Advantage speakers in an existing home, you will need to be diligent in locating existing pipes, ductwork, and AC wiring before cutting any holes in the ceiling or walls. In many cases, these obstructions are indicated by wall outlets, switches, plumbing fixtures, radiators, etc.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Advantage Contents High Frequency Switch IntroductionWoven Glass Fiber WOOFER/MIDRANGE Cone Large HIGH-ENERGY Magnetic Motor SystemsWall Requirements Acceptable Installation Situations Unacceptable Installation SituationsSpace Requirements & Impedance Matching Space RequirementsTransients TOO Much PowerSpeaker Care Getting Started & WHO Installer Skills and Tools Tools Needed for Installation in Existing WallsWhat Speaker Usage and Environment What Speaker Usage and EnvironmentRetrofit Installation When Pre-Construction or Retrofit InstallationDuring NEW INSTALLATION, Keep the Following Tips in Mind Where Speaker Placement Available locations unobstructed wall and ceiling surfacesStereo Imaging Home TheaterSurround Sound Where Speaker Placement Wire Considerations To Paint Speakers That have not Been Assembled or InstalledTo Paint Speakers That have Been Assembled and Installed HOW Cutting Wall/Ceiling Opening for Speakers HOW Cutting WALL/CEILING Opening for SpeakerRepeat steps 1 through 7 for the other speaker Junction BOX InstallationHOW Cutting Wall/Ceiling Openings for Speakers HOW Hooking up the Speakers AT the Speaker ENDRepeat Steps 1 through 5 for the other speakers Connect to the Amplifier no Wall Connector PlateConnect to the Amplifier Wall Connector Plate HOW Final Assembly of Speakers HOW Testing Speaker Polarity and Channel ConnectionsFor Focused Dispersion Twist the baffle clockwise until it locks into the slotsTo Test Polarity To Test Channel ConnectionsNo Sound from Either Speaker No Sound from ONE SpeakerSpecifications Speaker Specifications 25 13.3 cm woven glass fiber dualFrequency Response 16.5 cm woven glass fiber dualSpecifications Tweeter 20mm 0.8 aluminum dome, fluid cooledTweeter 25mm 1.0 aluminum dome, fluid cooled Nominal ImpedanceWarranty & Repair Warranty

In-Ceiling speaker specifications

Russound has long been synonymous with exceptional home audio solutions, and their in-ceiling speakers continue this tradition of quality and innovation. Designed to seamlessly blend into any room without sacrificing sound performance, these speakers are an optimal choice for those who want a clean aesthetic coupled with powerful sound delivery.

At the heart of Russound's in-ceiling speakers is their advanced driver technology. Equipped with high-quality woofers and tweeters, these speakers are engineered to deliver rich, full-bodied sound that is both immersive and dynamic. Whether you are listening to music, watching movies, or enjoying a podcast, the precision of these drivers ensures that every note and voice is reproduced with clarity and depth.

One standout feature of Russound in-ceiling speakers is their versatility. They are designed for various applications, whether your aim is to create a multi-room audio setup or fill a single room with sound. Their low-profile design allows for easy installation and makes them virtually invisible once mounted, allowing your decor to take center stage while providing an exceptional auditory experience.

Additionally, these speakers are often equipped with pivoting tweeters. This technology allows the sound to be directed towards your listening area, further enhancing the acoustic experience. The adjustable sound dispersion ensures uniform coverage, providing a balanced audio experience throughout the space.

Russound’s in-ceiling speakers are also built with durability in mind. Their construction materials are chosen to withstand the rigors of installation within ceilings while minimizing any unwanted resonance or distortion. This attention to detail is evident in both their performance and longevity, making them a reliable choice for years of enjoyment.

Moreover, compatibility with a range of home audio systems enhances their functionality. Whether you're integrating them into a dedicated home theater system or a distributed audio setup, Russound speakers are designed to work well with the latest audio components, ensuring seamless connectivity and a hassle-free experience.

In summary, Russound in-ceiling speakers offer an excellent blend of aesthetic appeal, advanced technology, and versatility. They promise to transform any living space into an audio haven, where quality sound meets seamless design. For those seeking a sophisticated sound solution that complements their lifestyle, Russound's in-ceiling speakers are a formidable option.
Top Page Image Contents