Russound Advantage Series owner manual Space Requirements & Impedance Matching, Wall Requirements

Page 4

Space Requirements & Impedance Matching

SPACE AND WALL REQUIREMENTS

SPACE REQUIREMENTS

Russound Advantage Iso-Mount speakers require a mini- mum wall depth of 3-5/8” (9.2 cm) (measured from the outside face of the mounting surface), and require at least 1.4 cubic feet of space behind the speaker for optimal performance.

WALL REQUIREMENTS

ACCEPTABLE INSTALLATION SITUATIONS:

•Any wallboard and 2x4 stud wall

•Lath and plaster wall

•Wood paneling and 2x4 stud wall. The dense, rigid nature of plasterboard (or lath and plaster) or thick wood paneling acts as a superb speaker baffle.

UNACCEPTABLE INSTALLATION SITUATIONS:

•Brick or concrete walls where the wallboard or panel- ing is attached to thin furring strips – This type of wall can’t provide proper depth (clearance) for the back of the Russound Advantage speakers.

•Locations concealing pipes, heating ducts and AC wiring – These elements can complicate speaker mounting and installation of speaker wire. AC wiring can induce hum caused by close proximity to the speaker.

IMPEDANCE MATCHING FOR AMPLIFIER AND SPEAKERS

Not all amplifiers or receivers can safely operate two sets of speakers at once. If you intend to run your Russound Advantage speakers and your main speakers concurrently, or if you intend to hook up and run two sets of speakers at the same time, it’s important to con- sider both the impedance of the speakers and the capa- bilities of the amplifier or receiver you’re using.

A speaker’s impedance rating indicates the amount of electrical resistance it places against current flowing from a receiver’s outputs. If the total speaker load does not present adequate resistance, the receiver increases its power output. Low-impedance speakers may hamper operations of receivers not designed to deliver large

amounts of current to low-impedance loads. This may lead to greater distortion, and causes the receiver to run hot or activate its protection circuitry.

First, consult the owner’s manual for your amplifier or receiver. It should state the minimum speaker imped- ance during multiple speaker operation. The impedance may also be printed on the back of the amplifier/receiv- er next to the speaker connectors. If you can’t readily determine this information, consult the dealer where you purchased the amplifier or receiver, or call the manufac- turer of the product in question.

The impedance rating for your Russound Advantage Music Series speakers is 8 ohms, 6 ohms for the Hi-Fi Series. Next, determine the impedance of your other speakers. It may be printed on the back of the speaker near the connection terminals, or you can consult the speaker’s owner’s manual. Speaker impedance must be equal to or higher than the amplifier/receiver speaker output impedance rating. For instance, an amplifier/receiver that is rated for two pair of 8 ohm speakers cannot support two pair of 4 ohm speakers.

If the amplifier/receiver is not rated for the speaker con- figuration desired, external volume controls and/or speaker selectors can maintain the impedance levels that will allow your amplifier/receiver to operate safely. Russound makes a complete line of these products, from Impedance-Matching Volume Controls to Impedance-Matching Speaker Selectors. Ask your Russound dealer for details or request a catalog from Russound at 800-638-8055 (U.S. and Canada) or +1- 603-659-5170 from outside the U.S.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Page Contents High Frequency Switch IntroductionRussound Advantage Large HIGH-ENERGY Magnetic Motor SystemsAcceptable Installation Situations Unacceptable Installation SituationsSpace Requirements & Impedance Matching Wall RequirementsTOO Much Power Speaker CareSpeaker Care TransientsRequirements? HOW How are the speakers installed? Getting Started & WHO Installer Skills and ToolsTools Needed for Installation in Existing Walls What Speaker Usage and Environment What Speaker Usage and EnvironmentDuring NEW INSTALLATION, Keep the Following Tips in Mind When Pre-Construction or Retrofit InstallationRetrofit Installation Where Speaker Placement Available locations unobstructed wall and ceiling surfacesStereo Imaging Home TheaterSurround Sound Fidelity Wire Wire Requirements Wire ConsiderationsHOW Painting the Speaker Frames and Grilles To Paint Speakers That have not Been AssembledTo Paint Speakers That have Been Assembled and Installed HOW Cutting Wall/Ceiling Opening for Speakers HOW Cutting WALL/CEILING Opening for SpeakerJunction BOX Installation Repeat steps 1 through 7 for the other speakerHOW Hooking up the Speakers AT the Speaker ENDConnect to the Amplifier Wall Connector Plate Connect to the Amplifier no Wall Connector PlateRepeat Steps 1 through 5 for the other speakers HOW Testing Speaker Polarity and Channel Connections HOW Final Assembly of SpeakersTo Test Polarity To Test Channel Connections Make sure sound emanates from all speakers in the systemNo Sound from Either Speaker No Sound from ONE SpeakerSpecifications Speaker Specifications Recommended Power SpecificationsFrequency Response Warranty & Repair WarrantyLR3130-0009

Advantage Series specifications

The Russound Advantage Series represents a pinnacle of innovation in the world of multi-room audio systems. Tailored for both residential and commercial applications, this series is designed to offer versatile, high-quality sound while ensuring user-friendly operations.

One of the key features of the Advantage Series is its modular design. This allows for easy expansion and customization to fit varying audio demands. Users can start with a basic setup and gradually add components to scale the system as needed. This flexibility is particularly beneficial for users who may be uncertain of their long-term audio needs.

Central to the Advantage Series is its high-performance audio technology. Utilizing advanced amplifiers and digital signal processing, the system delivers crystal-clear sound across all zones. The incorporation of innovative technologies ensures that listeners experience audio fidelity that meets or exceeds expectations regardless of the space or application.

The series also provides robust integration options. Russound has designed the Advantage Series to seamlessly integrate with a variety of third-party automation and control systems, such as HomeWorks and Crestron. This compatibility is crucial for creating a cohesive smart home experience, as it allows users to control their audio with user-friendly interfaces, whether through touchscreens, smartphone apps, or voice commands.

Another remarkable characteristic of the Advantage Series is its zone control capabilities. Users can create individual listening zones throughout their home or business, allowing different audio sources to play in different areas simultaneously. Each zone can be controlled independently, providing the ultimate in personalization and enjoyment.

User experience is further enhanced through the use of intuitive user interfaces. The Advantage Series offers a range of controller options, from wall-mounted keypads to mobile applications, ensuring ease of use for everyone. Additionally, the system supports both wired and wireless connections, offering flexibility in installation and operation.

In conclusion, the Russound Advantage Series is an outstanding choice for anyone seeking a sophisticated multi-room audio solution. With its modular design, high-quality audio performance, seamless integration, and user-friendly controls, the Advantage Series stands out as a leader in the audio industry, providing an immersive listening experience for any environment.
Top Page Image Contents