Retrofit Installation

WHEN – Pre-Construction or Retrofit Installation

WHEN - PRE-CONSTRUCTION OR RETROFIT INSTALLATION

PRE-CONSTRUCTION INSTALLATION Built-in speaker installation is more convenient during home construction than after construction is completed. Speaker wire can be routed to the destination before the wallboard is installed, and possible hindrances such as AC wiring, plumbing, or ductwork can be easily located and avoided.

Speaker rough-in brackets are used in the pre-construction phase of speaker installation during construction of new homes and additions. Russound offers Speaker Rough-In Brackets for the full line of Advantage speakers. These brack- ets are designed to provide drywall installers the correct cut- out pattern for the speakers. The brackets have “wings” that are nailed/screwed/stapled onto the wall studs. Once the wallboard is installed, the opening is cut out and the speaker frame is inserted into the bracket.

When installing the pre-construction bracket, note that there are holes molded into the bracket for speaker wire tie-off. This keeps the wire from getting lost later during the construction process. You can also tie the wire to the bezel/mounting assembly once it’s installed, using any of the rotating clamp towers.

DURING NEW INSTALLATION, KEEP THE FOLLOWING TIPS IN MIND:

•Use a small level to verify that the rough-in bracket is straight.

•If possible, run speaker wires after AC wiring is in place to avoid induced hum caused by close parallel proximity of the two types of wire.

•If possible, run speaker wires after plumbing is in place; wire can bend, pipes cannot.

•Secure speaker wires in place against a stud along vertical runs with insulated staples only, being careful not to pierce the wire insulation. Allow a bit of slack for expansion of building materials.

•Horizontal runs should be routed through holes drilled in studs at roughly equal heights.

•The actual speakers should not be installed until the wallboard is in place. In the meantime, leave several

Figure 2 New construction use of Rough-in Bracket

Not for use with Retrofit applications

2 x 4 STUD

feet of wire coiled up and secured to the back side of the mounting frame. Excess length can be removed during final assembly.

•Any speaker installed in a ceiling should have a safety wire firmly tied between the back of the speaker assem- bly and the frame of the building. Use any strong insu- lated wire and connect it to the speaker being careful not to let it interfere with the speaker’s operation. The other end should be firmly attached to the studs or floor- ing above using a hook, nail, or other reliable fastener.

•When installing the drywall, make sure the speaker cut-out hole doesn’t extend farther than 1/4” from the inside of the mounting frame. The flat rough-in brackets and wings are thin enough that they won’t interfere with wallboard installation.

•After the wallboard is secured, install the speakers as described in the installation instructions in this manual.

If you are installing Russound Advantage speakers in an existing home, you will need to be diligent in locating existing pipes, ductwork, and AC wiring before cutting any holes in the ceiling or walls. In many cases, these obstructions are indicated by wall outlets, switches, plumbing fixtures, radiators, etc.

Advantage Series specifications

The Russound Advantage Series represents a pinnacle of innovation in the world of multi-room audio systems. Tailored for both residential and commercial applications, this series is designed to offer versatile, high-quality sound while ensuring user-friendly operations.

One of the key features of the Advantage Series is its modular design. This allows for easy expansion and customization to fit varying audio demands. Users can start with a basic setup and gradually add components to scale the system as needed. This flexibility is particularly beneficial for users who may be uncertain of their long-term audio needs.

Central to the Advantage Series is its high-performance audio technology. Utilizing advanced amplifiers and digital signal processing, the system delivers crystal-clear sound across all zones. The incorporation of innovative technologies ensures that listeners experience audio fidelity that meets or exceeds expectations regardless of the space or application.

The series also provides robust integration options. Russound has designed the Advantage Series to seamlessly integrate with a variety of third-party automation and control systems, such as HomeWorks and Crestron. This compatibility is crucial for creating a cohesive smart home experience, as it allows users to control their audio with user-friendly interfaces, whether through touchscreens, smartphone apps, or voice commands.

Another remarkable characteristic of the Advantage Series is its zone control capabilities. Users can create individual listening zones throughout their home or business, allowing different audio sources to play in different areas simultaneously. Each zone can be controlled independently, providing the ultimate in personalization and enjoyment.

User experience is further enhanced through the use of intuitive user interfaces. The Advantage Series offers a range of controller options, from wall-mounted keypads to mobile applications, ensuring ease of use for everyone. Additionally, the system supports both wired and wireless connections, offering flexibility in installation and operation.

In conclusion, the Russound Advantage Series is an outstanding choice for anyone seeking a sophisticated multi-room audio solution. With its modular design, high-quality audio performance, seamless integration, and user-friendly controls, the Advantage Series stands out as a leader in the audio industry, providing an immersive listening experience for any environment.