GE PT960 manual 27/24 built-in single oven dimensions in inches, Models PK916, JKP70, JKP30, JKS10

27" built-in single ovens (continued)

27"/24" built-in single oven dimensions (in inches)

ge.com

27" models PK916, JKP70, JKP30, JKS10

Oven support for 27" models

C

L

2" x 4" or equivalent runners

10

Locate junction box either 5" MIN. below cutout floor or 44" MIN. above cutout floor

A

Allow 3/4" for overlap over all edges of cutout

B MIN.

Suitable bracing to support runners

18"

Over centerline

of cabinet

(Must support 275 lbs.)

D

Minimum

cutout location 32-1/2 from floor

(Minimum 15-5/8"
from floor when	2" x 4"
installed below built-in	or equiv.
microwave oven)	runners

G

F

E

C MIN.

Conduit 48-1/2" long

Oven support for 24" models

C

L

11"

over centerline

of cabinet

2 x 4 or equivalent runners

Note: These ovens are not approved for stackable or side-by-side installations.

Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent 45° and 90° walls should be placed to avoid interference with the handle.

Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at least a 194°F temperature rating.

Note: For 27" built-in single ovens, if marks, blemishes or the cutout opening is visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or openings are covered.

Undercounter installation dimensions (in inches)

Models PK916, JKP70, JKP30 and JKS10

Gas or electric cooktops may be installed over this

oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models.

		(Must support 275 lbs.)
Cabinet			PK916, JKP70/30, JKS10
A – Cabinet width required			27" min.
B – Minimum cabinet depth			23-5/8"
C – Opening width			25" min. - 25-1/4" max.
D – Opening height			27-5/8" min. - 28-1/8" max.
Oven
E – Overall depth*			23-5/8"
	w/o trim		29"
F – Overall height with trim			29-7/8" - 30-3/4"
G – Overall width			26-5/8"

*Depth including door handle is approximately 26-7/8" min to 26-8/10" max. 26-5/8" on models PK916, JKP70/30 and JKS10.

Sealed burner gas cooktop

	240V / 208V
25	Junction Box
	Location

5

25" MIN.

25 1/4" MAX.

Allow 1"

unit overlap

27 5/8" MIN.all edges

28 1/8" MAX.

Gas or electric connections for gas cooktop must be located in an adjacent accessible location to the right

22" MIN.	36"
Above	Typical
Support	Countertop
Platform	Height

installation dimensions (in inches)

5" To center of 2" diameter hole from countertop

90° Street el

45° Elbow	2" Diameter hole (20-7/8"
	from front of countertop
	to hole center)
Cabinet sides

3/4" Support Platform Required

Must Support 150 Lbs.

24

Note: 36" ribbon cooktops are approved for use over GE 30" single wall ovens* and warming drawers. 30" ribbon cooktops are approved for use over GE 30" and GE 27" single wall ovens* and warming drawers. Refer to cooktop and wall oven installation information packed with products for current dimensional data.

*Except wall ovens with Trivection® technology.

Standard burner gas cooktop installation dimensions (in inches)

		3-7/16" To center of 2" diameter
		hole from countertop
90° Street el		2" MIN. diameter hole
	45° Elbow	(23-1/4" from front
		surface of countertop)

Cabinet sides

Electric wall ovens are not approved for installation with a plug and receptacle. They must be hard wired in accordance with installation instructions.

Note: Oven is rated for use only under 30" standard or sealed burner gas and selected 30" CleanDesign and Calrod® electric cooktops.

Installation information: Before installing, consult installation instructions packed with product for current dimensional data.

Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at least a 194°F temperature rating.