GE UK-KIT-3S 4HANG THE ICEMAKER ON FREEZER WALL, 6PLACE ICE STORAGE BIN ON FREEZER SHELF

Page 9
4HANG THE ICEMAKER ON FREEZER WALL

Installation Instructions

INSTALLING THE ICEMAKER

4HANG THE ICEMAKER ON FREEZER WALL

Stainless steel clip

Slip the stainless steel clip over the wall of the water cup.

Screw one 5/8″ icemaker mounting screw in the top front hole. Leave the head out approximately 3/8″ for the slot in the icemaker hanger to slip over the screw.

 

Water fill

Start this

tube

Wire

screw first

harness

Hangers

outlet

 

Water

 

cup

Hold the icemaker in position inside the freezer. Insert the wire harness plug into the outlet using a rocking motion, until the locking fingers on the sides of the plug snap into place. The plug fits only one way.

Slip the icemaker hanger over the mounting screw, while easing the icemaker water cup toward the end of the water fill tube. The water fill tube fits under the stainless steel clip on the water cup. The water fill tube

must not be kinked. It should extend approximately 1/2″ into the water cup and must not become easily dislodged.

Screw in the two remaining icemaker mounting screws. Tighten all three screws.

5LIFT THE ICEMAKER FEELER ARM TO THE STOP (UP) POSITION.

Arm up— stops operation

Arm down— icemaker will operate

The icemaker should feel secure when you lift the arm. Leave the feeler arm in the STOP (up) position until the refrigerator is connected to the water supply to prevent it from operating before the water supply connection is complete.

6PLACE ICE STORAGE BIN ON FREEZER SHELF.

Feeler arm in STOP 6PLACE ICE STORAGE BIN ON FREEZER SHELF.7APPLY WARRANTY LABEL TO BACK OF REFRIGERATOR. (up) position

Move the ice storage bin into place directly under the icemaker.

NOTE: Check again to make sure the icemaker power cord is fully inserted into its outlet.

Check again to make sure the icemaker feeler arm is in the STOP (up) position.

7APPLY WARRANTY LABEL TO BACK OF REFRIGERATOR.

A label is provided in the kit. On it record the date of the installation for warranty purposes.

The icemaker installation is now complete. Refer to the following instructions for connecting the icemaker to the home water supply.

9

Image 9
Contents Troubleshooting Tips Icemaker Accessory KitInstallation Instructions Operating InstructionsSAFETY PRECAUTIONS READ AND SAVE THESE INSTRUCTIONSREAD AND FOLLOW THIS SAFETY INFORMATION CAREFULLY For Your SafetyAbout the automatic icemaker How to Use Your IcemakerHow the Icemaker Works Troubleshooting Tips Before you call for service…Problem Possible Causesor “shrink” to icemaker on some modelsUnit is leaking water ADDITIONAL MATERIALS YOU WILL NEED BEFORE YOU BEGINInstallation Instructions UK-KIT-3SIcemaker Accessory KitCONTENTS OF UK-KIT-3S Installation InstructionsBEFORE YOU BEGIN ICE MAKER1REMOVE THE ICE SERVICE RACK INSTALLING THE ICEMAKER4HANG THE ICEMAKER ON FREEZER WALL 6PLACE ICE STORAGE BIN ON FREEZER SHELF7APPLY WARRANTY LABEL TO BACK OF REFRIGERATOR INSTALL THE WATER VALVE WATER VALVE INSTALLATION INSTRUCTIONSWATER LINE INSTALLATION INSTRUCTIONS WARRANTY INFORMATIONWHAT YOU WILL NEED TYPICAL PLUMBING INSTALLATION WITH WATER SUPPLY KITS WX8X2, WX8X3 and WX8X41SHUT OFF MAIN WATER SUPPLY 6TURN ON WATER AND CHECK ALL JOINTS FOR LEAKS 5CONNECT WATER SUPPLY TUBING TO REFRIGERATOR9MOVE THE REFRIGERATOR BACK TO THE WALL Page GE Will Replace Icemaker WarrantyWhat GE Will Not Cover or call 800.GE.CARESParts and Accessories Schedule ServiceConsumer Support GE Appliances Website