Monogram.“
ZIF36NM – GE Monogram 36" Built-In All-Freezer
1/4" Accessory Panels:
Factory trim accepts accessory panel kits. Panels are cut to size and ready to install. Kits must be ordered separately.
Custom Panels – Match the cabinetry! ZKTR36LH for ZIR36NMLH, ZIF36NMLH ZKTR36RH for ZIR36NMRH, ZIF36NMRH
|
|
|
| Provides for the installation of 3/4" thick custom door and grille | |
| White | Black | Stainless | ||
| panels. Use this kit for a trimless appearance. This kit provides | ||||
Models | Lexan® | Lexan® | Steel | ||
a standard handle to fit the 3/4" panel. | |||||
ZIR36/ZIF36 | ZWWR36 | ZWBR36 | ZWSR36 | ||
Grille Panel – For Installation height adjustments! | |||||
Door Handles – To match or complement cabinetry! | |||||
ZGC2 – Provides 1/4" grille panel frame side pieces for | |||||
ZKHR1 – Provides the necessary framework to install a custom | |||||
and | |||||
handle of your choice, onto a 1/4" thick custom panel. (Handle | is set for 84". | ||||
not included.) |
|
|
|
| |
ZKHTR1 – Provides the necessary framework to install a cus- | |||||
ZUG75 Trim Kit – For | |||||
tom handle of your choice, onto a 3/4" thick custom panel. | |||||
units. This kit provides for the | |||||
(Handle not included.) This kit must be used in combination with | |||||
installation of a unified 3/4" grille | |||||
ZKTR36LH or ZKTR36RH. |
|
| |||
|
| panel to span the width of two | |||
ZKHRSS1 – Tubular stainless steel handle for 1/4" thick panel | units. This kit contains a trim | ||||
installation. |
|
|
| strip to cover the inside case | |
ZKHTRSS1 – Tubular stainless steel handle for 3/4" thick panel | trim for a finished appearance. | ||||
installation. This kit must be used in combination with ZKTR36LH | This kit must be used in | ||||
or ZKTR36RH. |
|
|
| combination with BOTH the | |
|
|
|
| ZKTR36LH and ZKTR36RH kits. | |
|
| ||||
• Side panels are required whenever the sides of the | • If you choose to use 1/4" side panels, they should be inserted into | ||||
product will be exposed and when | installed between | the case trim as illustrated. Fasten the panels to the product | |||
frameless cabinets. |
|
| with | ||
• Side panels are not required when installed into |
| setting in place. See illustration A. | |||
an enclosure. |
|
|
| • 1/2" to 3/4" side panels are normally set into place and fastened | |
• Side panel installation will be determined by the design | to adjacent cabinetry or the back wall before rolling the product | ||||
of the side panel you have previously chosen. |
| into the opening. See illustration B. | |||
• Side panels must be installed plumb. |
|
| |||
Illustration A | 23 9/16" | |
1/4" Side Panels – Insert |
|
|
end of side panel into case |
|
|
trim. Fasten with hook and |
|
|
loop strips. |
|
|
|
|
|
| 84" | |
Trim |
|
|
|
|
|
Top View | 2 9/16" | |
|
| |
Standard 4" high toekick or trim to fit. Height may vary depending on application.
Specification Revised 4/05 110156
Illustration B | 24 3/4" | |
1/2" to 3/4" Side Panels – |
|
|
Leading edge of side panel |
|
|
is flush with cabinet front. |
|
|
Fasten to the back wall |
|
|
using a cleat. |
|
|
|
|
|
| 84" | |
3 3/4"
Top View
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
|
| For answers to your Monogram,® GE Profile™ or |
| Listed by | GE appliance questions, visit our website at |
| Underwriters | GEAppliances.com or call |
R | Laboratories | GE Answer Center® service, 800.626.2000. |
|
|