GE JGRP20 Using the self-cleaning oven, Before a Clean Cycle, How to Set the Oven for Cleaning

Page 23

Using the self-cleaning oven.

ge.com

The oven door must be closed and all controls set correctly for the cycle to work properly.

Safety

Wipe up heavy soil on the oven bottom.

Before a Clean Cycle

For the first self-clean cycle, we recommend venting your kitchen with an open window or using a ventilation fan or hood.

Remove shelves, broiler pan, broiler grid, all cookware and any aluminum foil from the oven.

The shiny, silver-colored oven shelves (on some models) can be self-cleaned, but they will darken, lose their luster and become hard to slide.

Soil on the front frame of the oven and outside the gasket on the door will need to be cleaned by hand. Clean these areas with hot water, soap-filled scrubbing pads or cleansers such as Soft Scrub®. Rinse well with clean water and dry.

Do not clean the gasket. The fiberglass material of the oven door gasket cannot withstand abrasion. It is essential for the gasket to remain intact. If you notice it becoming worn or frayed, replace it.

Wipe up any heavy spillovers on the oven bottom.

Make sure the oven light bulb cover is in place and the oven light is off.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any oven.

Move birds to another well-ventilated room.

Instructions

Operating

How to Set the Oven for Cleaning

Touch the SELF CLEAN pad.

Touch the + or pad to enter the desired clean time, if a time other than 4 hours is needed.

Clean cycle time is normally 4 hours.

You can change the clean time to any time between 3 hours and 5 hours, depending on how dirty your oven is.

Touch the START pad.

The door locks automatically. The display will show the clean time remaining. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCKED DOOR light goes off.

When the LOCKED DOOR light is off, open the door.

The oven shuts off automatically when the clean cycle is complete.

NOTES:

The words LOCK DOOR will flash and the oven control will signal if you set the clean cycle and forget to close the oven door.

To stop a clean cycle, touch the

CLEAR/OFF pad. When the LOCKED DOOR light goes off indicating the oven has cooled below the locking temperature, open the door.

Instructions

Troubleshooting Tips

How to Delay the Start of Cleaning

Delay Start is setting the oven to start the clean cycle automatically at a later time than the present time of day.

NOTE: Before beginning, make sure the oven clock shows the correct time of day.

Touch the SELF CLEAN pad.

Touch the + or pad to enter the desired clean time.

Touch the DELAY START pad. The earliest start time you can set will appear in the display.

Touch the + or pad to enter the time of day you want the clean cycle to start.

Touch the START pad.

The door locks automatically. The display will show the start time. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCKED DOOR light goes off.

When the LOCKED DOOR light is off, open the door.

NOTE:

You can find out when the clean cycle will start by touching the DELAY START pad.

Consumer Support

23

Image 23
Contents Write the model and serial numbers here Model # Serial # Built-In GasWhat to do if YOU Smell GAS Ge.com Important Safety NoticeCook Meat and Poultry THOROUGHLY… Oven SELF-CLEANING Oven Oven Control, Clock and Timer Features and Settings Using the oven controlsUsing the clock and timer Tones While Setting the Control Preheat Notification Tone Power FailureCook and Hold Special features of your oven controlTones at the End of a Timed Cycle Hour Shut-OffChanging the Speed of the +/- Pads Fahrenheit or Centigrade Temperature SelectionHour, 24-Hour or Clock Black-Out Control LockoutUsing the oven Oven Shelves Shelf PositionsOven Moisture Preheating Using the baking featureHow to Set Your Oven for Baking Oven ShelvesCakes Baking PansCookies PiesHow to Set Immediate Start and Automatic Stop Using the timed baking featureHow to Set Delay Start and Automatic Stop Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat Before You Begin Roasting… Using the roasting featureHow to Set Your Oven for Roasting Why is my roast crumbling when I try to carve it? Questions and AnswersBefore You Begin Broiling… Using the broiling featureHow to Set Your Oven for Broiling Comments Broiling GuideSafety Using the self-cleaning ovenBefore a Clean Cycle How to Set the Oven for CleaningShould there be any odor during the cleaning? After a Clean CycleOven Air Vents Care and cleaning of the ovenHow to Remove Protective Shipping Film and Packaging Tape Removable Storage DrawerDo not remove any screws to remove the cover Oven Light ReplacementSelf-clean cycle Removable Oven BottomLift-Off Oven Door To clean the inside of the doorTo clean the outside of the door Control PanelBroil and Oven Burner Air Adjustment Shutters Adjusting Orifice HoodsBefore you call for service… Crackling or See the Using the self-cleaning oven sectionAfter a clean cycle Oven not clean after a Clean cycleDisplay flashes Power outageCall for service On outer cones Display goes blankPage We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration One Year GE Gas Oven WarrantyGE Will Replace, At No Charge To You What GE Will Not CoverReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website
Related manuals
Manual 36 pages 27.19 Kb

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.