GE JGRP20 owner manual Adjusting Orifice Hoods, Broil and Oven Burner Air Adjustment Shutters

Page 28

Care and cleaning of the oven.

Safety Instructions

 

Adjusting Orifice Hoods

Nat.

Check the inner cones of the flames.

 

The inner cones of the flames should be

L.P.

about 1/2″ long. If the flames are not

right, use a 1/2″ open-end wrench or

adjustable joint pliers to adjust the orifice hood.

WARNING: If you attempt to measure the inner cone of the flame, please use caution. Burns could result.

To shorten the cones, tighten the orifice hood by turning in the “L.P.” direction. To lengthen the cones, loosen the orifice hood by turning in the “Nat.” direction.

Loosen

Broil and Oven Burner Air Adjustment Shutters

Operating Instructions

Troubleshooting Tips

Consumer Support

Air

adjustment

shutter

Shutter for top burner

Loosen

Air adjustment shutter

Shutter for bottom burner

Flames for top burner

Flames for bottom burner

28

Air adjustment shutters for the broil and oven burners regulate the flow of air to the flame.

All ovens are factory adjusted for use with the natural gas used in most areas. But, since the gas in some areas may be different, you should check all adjustments described. If you are using LP gas, all the adjustments must be made.

The air adjustment shutter for the top burner is in the center of the rear wall of the oven.

The shutter for the bottom burner is near the back wall. Remove the oven bottom for access.

Turn the burner full on and check the flames. The burner flames should not flutter or blow away from the burner.

They should be blue in color with no trace of yellow. Foreign particles in the gas line may cause an orange flame at first, but this will soon disappear. If the flames are yellow or flutter, open the air shutter more. If they blow away from the burner, close the air shutter more. See the illustration in the Troubleshooting Tips of this guide for correct flame appearance.

To adjust the flow of air to either burner, loosen the Phillips head screw and rotate the shutter to allow more or less air into the burner tube as needed.

The flames for the top (broil) burner should burn steady with approximately 1″ blue cones and should not extend out over the edges of the burner baffle.

To determine if the bottom burner flames are proper, remove the oven bottom and the burner baffle. The flames should have 1/2″ to 3/4″ blue cones with no yellow tipping. When the baffle is back in place, the flames will resettle.

Visually check the color of the flames every 6 months. If they look like illustration (A) in the Troubleshooting Tips in this guide, call for service.

When checking the flames, before and after adjustments, the oven door should be closed.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Built-In Gas Write the model and serial numbers here Model # Serial #What to do if YOU Smell GAS Important Safety Notice Ge.comCook Meat and Poultry THOROUGHLY… Oven SELF-CLEANING Oven Using the oven controls Oven Control, Clock and Timer Features and SettingsUsing the clock and timer Power Failure Tones While Setting the Control Preheat Notification ToneSpecial features of your oven control Tones at the End of a Timed CycleHour Shut-Off Cook and HoldFahrenheit or Centigrade Temperature Selection Hour, 24-Hour or Clock Black-OutControl Lockout Changing the Speed of the +/- PadsUsing the oven Oven Moisture Shelf PositionsOven Shelves Using the baking feature How to Set Your Oven for BakingOven Shelves PreheatingBaking Pans CookiesPies CakesUsing the timed baking feature How to Set Immediate Start and Automatic StopHow to Set Delay Start and Automatic Stop To Adjust the Thermostat Adjust the oven thermostat-Do it yourselfType of margarine will affect baking performance How to Set Your Oven for Roasting Using the roasting featureBefore You Begin Roasting… Questions and Answers Why is my roast crumbling when I try to carve it?How to Set Your Oven for Broiling Using the broiling featureBefore You Begin Broiling… Broiling Guide CommentsUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning SafetyAfter a Clean Cycle Should there be any odor during the cleaning?Care and cleaning of the oven How to Remove Protective Shipping Film and Packaging TapeRemovable Storage Drawer Oven Air VentsOven Light Replacement Self-clean cycleRemovable Oven Bottom Do not remove any screws to remove the coverTo clean the inside of the door To clean the outside of the doorControl Panel Lift-Off Oven DoorAdjusting Orifice Hoods Broil and Oven Burner Air Adjustment ShuttersBefore you call for service… See the Using the self-cleaning oven section After a clean cycle Oven not clean after aClean cycle Crackling orPower outage Call for service On outer conesDisplay goes blank Display flashesPage We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Gas Oven Warranty GE Will Replace, At No Charge To YouWhat GE Will Not Cover One YearSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio
Related manuals
Manual 36 pages 27.19 Kb

JGRP20 specifications

The GE JGRP20 is a prominent jet engine widely used in modern aviation, recognized for its efficiency, power, and advanced engineering. Developed by General Electric, this engine serves as a key component in various commercial and military aircraft, offering a blend of performance and reliability that meets the demands of today's dynamic air transport sector.

One of the primary features of the JGRP20 is its advanced turbofan design, which allows for improved fuel efficiency and lower emissions compared to older engine models. The engine incorporates cutting-edge materials such as advanced composites and titanium alloys, which contribute to its lightweight structure while ensuring durability and longevity. This makes the JGRP20 an environmentally friendly choice, aligning with global efforts to reduce the carbon footprint of aviation.

The engine boasts a high bypass ratio, which enhances its thrust capabilities while operating at lower noise levels. This is particularly advantageous for urban airports where noise regulations are stringent. The combination of high bypass ratio and advanced aerodynamics enables the JGRP20 to deliver superior performance during takeoff and cruising phases of flight.

Advanced technologies integrated into the GE JGRP20 include digital engine control systems, which optimize performance and efficiency throughout the flight. With real-time monitoring and data analysis, the engine can adapt to varying flight conditions, ensuring optimal fuel consumption and thrust. Furthermore, the engine's component health monitoring system provides invaluable insights into the operational status, allowing for predictive maintenance and minimizing downtime.

In terms of operational versatility, the JGRP20 can be tailored to suit a range of aircraft configurations, making it a flexible solution for airlines and military operators alike. Its capacity for various thrust settings allows it to power a wide array of aircraft from regional jets to larger commercial airliners.

In summary, the GE JGRP20 represents the pinnacle of jet engine design and technology. With its commitment to efficiency, reduced emissions, and noise reduction, alongside its robustness and adaptability, it stands as a trusted choice for aviation stakeholders seeking reliable and high-performing engines for their fleets. This engine not only exemplifies GE's engineering prowess but also highlights the industry's ongoing evolution towards more sustainable air travel practices.
Top Page Image Contents