GE PP975, PP945 manual Cooktop Components, Cooktop Removal From Countertop, Glass Top

Page 15

Cooktop Components

WARNING: Before servicing the cooktop, power must be removed from the cooktop by turning the power off at the circuit breaker.

WARNING: Sharp edges may be exposed when servicing. Use caution to avoid injury. Wear Kevlar gloves or equivalent protection.

Cooktop Removal From Countertop

To remove the cooktop from the countertop:

Caution: The hold-down brackets and screws on the bottom of the burner box can damage the countertop surface. Use care to protect the countertop appearance.

1.Remove screws that attach the hold-down brackets to the inside of the cabinet.

Note: In the following step, it will be necessary to utilize 2 strips of wood or cardboard.

2.Push upward on the bottom of the burner box approximately 4 in. and rotate slightly left or right (to the best working advantage). Shim under the burner box with protective wood or cardboard as shown.

3.Remove the mounting screw and hold-down bracket from each side of the cooktop.

Glass Top

Note: The ceramic glass top and touch board will be supplied as a complete assembly. If the touch board is damaged or defective, the entire glass top assembly must be replaced.

To replace the glass top:

Caution: To prevent electrostatic discharge that can damage electronic controls, ground yourself to the metal burner box or use an ESD wristband.

1.Remove the cooktop from the countertop. (See

Cooktop Removal From Countertop.)

2.Remove all screws along the top edge on all 4 sides of the burner box.

3.Slowly lift the front of the glass top (PP975), or the right side of the glass top (PP945), approximately 6 inches.

4.With the glass top tilted at an angle, disconnect the wire harness that extends from the daughter relay module (DRM) to the user interface by pulling downward on the connector. Do not pull on the wires.

+

-

+

-

+

-

+

-

+

-

Mounting

Connector

Screw

 

 

Harness

Model PP975 Shown

5.Remove the glass top from the burner box. Place the glass top on a protected surface.

– 15 –

Image 15
Contents Technical Service Guide Important Safety Notice Table of Contents Serial Number Nomenclature9 7 5 B M 1 B B Model NumberIntroduction Model Number PP945Model Number PP975 Electrical Requirements InstallationDimensions and Clearances Overall Cooktop Dimensions 36-in. ModelsOverall Cooktop Dimensions 30-in. Models Features of your cooktop Control FeaturesUsing the surface elements Single Surface Element Control Lock Digital Control System Operation OverviewComponent Locator Views Front View Model PP945Top View Glass Top Removed Front View Model 975PP Cooktop Components Cooktop Removal From CountertopGlass Top Daughter Relay Module DRM To replace the DRMModel PP975 Model PP945 To replace the Rpsm Relay Power Supply Module RpsmTo remove heating elements Heating ElementsTab Mark Number Component Quick Reference Troubleshooting Diagnostics and Service InformationElement Resistance Troubleshooting Model PP Test Location Element Hot Light TroubleshootingModel PP945 Element 240 VAC Schematic Schematics and Wiring DiagramsWiring Diagram Model PP945 Model PP975 Element 240 VAC Schematic Wiring Diagram Model PP975 For The Period Of GE Will Provide Warranty
Related manuals
Manual 40 pages 27.84 Kb

PP975, PP945 specifications

The GE PP945 and PP975 are two advanced gas ranges that showcase General Electric's commitment to innovation, performance, and user convenience. These models have become popular choices among home chefs looking for reliable appliances that optimize cooking experiences.

The GE PP945 features an induction cooktop with four cooking elements that provide precise temperature control and rapid heat adjustment. Induction technology is notable for its ability to heat cookware directly, leading to faster cooking and additional energy efficiency. With its sleek design, this model not only enhances kitchen aesthetics but also enables easy cleaning thanks to its flat surface. The oven in the PP945 provides true European convection, which utilizes a fan and additional heating element to circulate hot air evenly throughout the oven cavity. This results in improved baking performance and more consistent results across multiple racks.

On the other hand, the GE PP975 takes cooking convenience a step further with its range of smart features, including Wi-Fi connectivity that allows users to control their oven remotely via a smartphone app. This capability enables home cooks to preheat the oven or adjust cooking settings from virtually anywhere, adding unparalleled convenience to meal preparation. The PP975 also features a self-cleaning option, utilizing high-temperature cleaning to reduce food residue to ash, making maintenance simple and hassle-free.

Both models are equipped with a variety of cooking modes, including bake, broil, and various convection options, catering to diverse culinary techniques. The advanced oven design includes steam-cleaning options, which offer homeowners an environmentally friendly and efficient way to tackle spills and splatters without harsh chemicals.

Additional features include oven racks that are easily adjustable, precise temperature probes for meat, and large capacity ovens that can accommodate multiple dishes simultaneously. Safety features such as automatic shut-off and a child lock ensure that cooking remains safe for families.

In summary, the GE PP945 and PP975 are designed for those seeking a blend of modern technology and traditional cooking styles. With standout features such as induction cooking, smart technology, and efficient cleaning options, both ranges are well-equipped to enhance the cooking experience and meet the demands of today’s culinary enthusiasts. Whether you choose the PP945 for its induction efficiency or the PP975 for its smart capabilities, both models represent the forefront of cooking innovation.