Installation of the cooktop, Before You Begin

and Cleaning Operating Instructions Safety Instructions

Installation of the cooktop.

Read these instructions completely and carefully.

Before You Begin

Read these instructions completely	NOTE TO INSTALLER—Be sure to leave these
and carefully.	instructions with the Consumer.
IMPORTANT—Save these instructions	NOTE: This appliance must be properly
for local inspector’s use.	grounded.
IMPORTANT—Observe all governing codes
and ordinances.

Tools You Will Need

■ 1/8″ Drill bit	■ Pencil
■ Electric or hand drill	■ Ruler or tape measure and straightedge
■ Flat blade screwdriver	■ Hand saw or saber saw

Electrical Requirements

Tips Installation Instructions Care

		CAUTION: for personal safety, remove
		house fuse or circuit breaker before beginning
		installation.
		This appliance must be supplied with the proper
		voltage and frequency and connected to an
		individual, properly grounded branch circuit,
		protected by a circuit breaker or time delay fuse,
		as noted on the rating plate.
		All wire connections must be made in accordance
	Rating plate is	with local codes and properly insulated. Check
	Rating plate is	with your local utility for governing electrical
	located on the	with your local utility for governing electrical
	bottom center front	codes and ordinances.
	of the cooktop

In the absence of local electrical codes, the National Electrical Code, ANSI/NFPA No. 70–Latest Edition, governing electric range installations, must be followed.

A copy of the National Electrical Code can be obtained by writing to:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02260

If you fail to wire your counter unit in accordance with governing codes, you may create a hazardous condition.

Electrical Connections

Consumer Support Troubleshooting

DANGER: The electrical power to the counter unit supply line must be shut off while line connections are being made. Failure to do so could result in serious injury or death.

You must use a two-wire A.C. 208/240 Volt,

60 Hertz electrical system. A white (neutral) wire is not needed for this unit. The white lead from the household electrical supply can be isolated and secured in the junction box. If you connect to aluminum wiring, properly installed connections listed for use with aluminum and copper wiring must be used.

Use a minimum wire size of No. 12 copper wire with a 20 Amp fuse or circuit breaker for both 208/240 Volt electrical systems.

When making the wire connections, use the entire length of conduit provided. The conduit must not be cut.

Connect the red and black leads from the counter unit conduit to the corresponding leads in the junction box.

The bare ground wire in the conduit is connected to the counter unit frame. It must be connected to the household electrical supply ground.

JP202 specifications

The GE JP202 is a revolutionary product that represents a significant advancement in the realm of energy generation technology. This cutting-edge gas turbine offers remarkable efficiency and reliability, making it an ideal choice for both utility and industrial applications. Designed by General Electric, a leader in energy solutions, the JP202 has been engineered to meet the growing demands for cleaner and more sustainable energy sources.

One of the main features of the JP202 is its high efficiency. The gas turbine operates with an efficiency rating of up to 64%, positioning it as one of the most efficient gas turbines in its class. This efficiency not only results in reduced fuel consumption but also contributes to lower greenhouse gas emissions, aligning with global goals for environmental sustainability.

The JP202 utilizes advanced aerodynamics and materials technology that enable superior performance under various operating conditions. Its advanced cooling technologies allow for higher operating temperatures, which are crucial for improving overall efficiency. The turbine's combustion system is engineered to minimize NOx emissions, further enhancing its environmental performance without compromising on power output.

Another key characteristic of the JP202 is its modular design. This makes maintenance and upgrades easier, ensuring that operators can maximize uptime and reduce operational costs. The design facilitates quick access to critical components, which allows for streamlined service and maintenance routines.

The turbine is equipped with a sophisticated digital control system that enhances its operational flexibility. This system utilizes advanced analytics and machine learning algorithms to optimize performance in real-time. Operators can monitor and control the turbine remotely, allowing for improved decision-making and operational efficiency.

In addition to its technological innovations, the GE JP202 is designed with versatility in mind. It can operate on various fuel types, including natural gas, biogas, and other renewable fuels, allowing facility operators to adapt to changing fuel markets and regulations. Its design is suitable for combined cycle operations, which further enhances its efficiency by capturing waste heat to produce additional power.

In summary, the GE JP202 combines high efficiency, innovative technologies, and a modular design to provide a powerful solution for modern energy needs. Its commitment to reducing emissions and promoting sustainability makes it a valuable asset for energy generation, ensuring reliable power while supporting environmental goals. This turbine is poised to play a significant role in the transition to cleaner energy sources.