GE 164D3333P235 Observe the following points in canning, What is a temperature limiter?

Page 12

Home Canning Tips

Radiant Cooktop

Observe the following points in canning

Note: Flat-bottomed canners are required for glass cooktops.

Pots that extend beyond 1 inch of the surface unit’s circle are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to the cooktop surfaces surrounding the surface units.

HOWEVER, DO NOT USE LARGE DIAMETER CANNERS OR OTHER LARGE DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures—and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm the glass cooktop surfaces.

1.Be sure the canner fits over the center of the surface unit. If your cooktop or its location does not allow the canner to be centered on the surface unit, use smaller diameter pots for good canning results. Do not allow the canner to overlap the countertop.

2.Flat-bottomed canners must be used. Do not use canners with flanged or rippled bottoms (often found in enamelware) because they don’t make enough contact with the surface units and take a long time to boil water.

3.When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball and Kerr brand; and the United States Department of Agriculture Extension Service.

Right!Wrong!

4.Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.

NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed. The process time will be shortened by:

(1)using a pressure canner, and

(2) starting with HOT tap water for fastest heating of large quantities of water.

CAUTION:

•Safe canning requires that harmful microorganisms are destroyed and that the jars are sealed completely. When canning foods in a water-bath canner, a gentle but steady boil must be maintained for the required time. When canning foods in a pressure canner, the pressure must be maintained for the required time.

•After you have adjusted the controls, it is very important to make sure the prescribed boil or pressure levels are maintained for the required time.

•Since you must make sure to process the canning jars for the prescribed time, with no interruption in processing time, do not can on any cooktop surface unit if your canner is not flat.

What is a temperature limiter?

12

Every radiant surface unit has a temperature limiter.

The temperature limiter protects the glass cooktop from getting too hot.

The temperature limiter may cycle the units off for a time if:

•the cooktop is on while cooking.

•the pan boils dry.

•the pan bottom is not flat.

•the pan is off center.

•there is no pan on the unit.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Radiant Cooktop Contents IntroductionRemove packaging tape Before using your cooktop If you need serviceWrite down the model Serial numbers If you received a damaged cooktop Save time & moneySafety Precautions Safety Precautions Safety Precautions Features of Your Cooktop Design informationHow to set the controls Radiant surface units Do not use the surface as a cutting boardUsing the bridge surface unit Using the dual surface unit Turn the control knob to the desired settingRight front surface unit has 2 cooking sizes to select From so you can match the size of the unit to the sizeTypes of cookware RecommendedStoneware usable, but not recommended Glass-ceramicusable, but not recommendedWhat is a temperature limiter? Observe the following points in canningControl knobs Daily cleaning Glass Cooktop Cleaning For heavy, burned-on soil…Special care for sugary spills Before You Call For Service… Save time and moneyRegistration Ownership Product Consumer Consumer Product Ownership Registration In-Home Repair Service Service Contracts 800 Parts AccessoriesGE Answer Center 800.626.2000 For Customers With Special Needs… 800.626.2000Warranty Replacement radiant surface unit if it should burn out

164D3333P235 specifications

GE 164D3333P235 is a sophisticated and robust component designed for specific applications in industrial and commercial sectors. This component is part of General Electric’s extensive portfolio of high-performance systems and accessories. It showcases innovative technologies and engineering excellence synonymous with the GE brand.

One of the main features of the GE 164D3333P235 is its exceptional reliability. It is engineered to endure demanding operating environments, making it suitable for industries that require consistent performance under various conditions. The construction of this unit emphasizes durability, ensuring a long life span that minimizes the need for frequent replacements or repairs.

The GE 164D3333P235 is equipped with state-of-the-art technology that enhances its functionality. It often includes advanced electronic controls that streamline operations and improve energy efficiency, which is critical in today's energy-conscious landscape. This component is designed to support complex automation systems, allowing for seamless integration with other GE technologies and third-party systems.

Another characteristic that stands out is its versatility. The GE 164D3333P235 can be utilized in a range of applications, from manufacturing and factory automation to utilities and infrastructure management. This adaptability makes it a valuable solution for businesses looking to enhance their operational capabilities.

Safety features are also a priority in the design of the GE 164D3333P235. It typically includes built-in safeguards to protect against common electrical hazards, ensuring that users can operate the equipment with confidence. These features are crucial for compliance with industry standards and regulations.

In terms of user-friendliness, the GE 164D3333P235 often comes with comprehensive documentation and support resources, allowing operators to easily understand and utilize its capabilities. Training programs and customer support services may be available, which can further enhance the user's experience and efficiency.

In conclusion, the GE 164D3333P235 exemplifies the innovation and reliability GE is known for. With its advanced technologies, versatile applications, and robust safety features, it stands out as a crucial component for businesses looking to enhance productivity and efficiency while minimizing operational risks.
Top Page Image Contents