BEFORE YOU START
PAGE 2 OF 6
DO Ensure the countertop is square and level and ensure no structural members interfere with space requirements.
DO Ensure that there is a power supply receptacle within reach of the cooktop power cord (30" from the middle of the product). The main cable should not touch any
hot metal parts.
DO Make sure the cooktop is connected to a power supply socket that is electrically grounded in accordance with local codes or in the absence of local codes, with the National Electric Code ANSI/FPA 70 or CSA 22.2 (Canada).
DO Make sure the countertop is made of a heat resistant material.
WARNINGS
This appliance shall be installed in accordance with the installation requirements of the local gas authority or the appropriate installation code or in the absence of local codes with the latest National Fuel Gas Code ANSI Z223.1 or CAN B149.1,2(Canada).
Disconnect power before servicing unit.
Be aware of sharp edges when handling stainless steel products. (Carry the product using the polystyrene ends).
When this appliance is installed it shall not be used as a space heater.
No combustible material or products should be placed on this appliance at any time. Do not spray aerosols in the vicinity of this appliance while it is in operation.
Not to be installed in a bathroom or bedroom/sleeping quarters.
Flexible appliance connectors shall meet the requirements of ANSI Z21.24 and State Boards. They shall not exceed 36 inches in length.
PRODUCT & CUTOUT DIMENSIONS
GC36
Clamping Down the Cooktop
Place the cooktop into the cutout and tighten it with the supplied clamps. These will cope with the countertop thicknesses 5/8"- 2" (see diagram below) when used in the two orientations shown.
.5mm) |
| 36" | (914mm) | ||
|
| ||||
21" |
|
|
|
| |
(533 |
|
|
|
|
|
1 | 5 |
|
|
|
|
| / | " |
|
|
|
| 8 | (41. |
|
| |
|
| 5mm) |
|
| |
|
|
|
|
| |
GC901/M
Clamping Down the Cooktop
Place the cooktop into the cutout and tighten it with the supplied clamps. These will cope with the countertop thicknesses 3/4"- 2" (see diagram below) when used in the two orientations shown.
1 | " |
|
|
|
|
| 36" | (914mm) |
|
|
|
|
|
| |||
(546mm) |
|
|
|
|
|
| ||
21 | / 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
GC901: | 2 | 9 |
|
|
|
| ||
GC901M: |
| / | " | (65mm) |
| |||
|
|
| 3" | 16 |
| |||
|
|
|
|
| (76mm) |
| ||
Do not over tighten
19
|
|
|
|
|
|
| " |
|
|
|
|
| 3 | / | 8 |
3 | / | 4 | - 478mm) | ||||
|
| " | - | 18 |
|
| |
|
|
|
|
| |||
|
|
|
|
|
|
| |
(501 |
|
|
|
| |||
R 1/4" - 1/2"
|
| 34 | 3 |
|
|
|
|
|
|
|
|
| / | " |
|
|
|
| |
2minimum3 | (882 - | 4 | - | 33 | 3 |
| |||
|
|
|
|
|
| " | |||
8" |
|
|
| 846mm) |
| ||||
|
|
|
|
|
|
|
| / |
|
/ | (60 |
|
|
|
|
|
| 8 |
|
mm) |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
Do not over tighten
20
|
| ” |
5 | / | 8 |
|
| |
(524 | ||
- -
|
| ” |
1 | / | 8 |
486mm) | ||
19 |
|
|
R 3/16" - 1/2"
|
| 35 | 1 |
|
|
|
|
|
|
|
| |
|
|
|
| / | " |
|
|
|
|
| ||
|
| (895 - |
| - 33 | / |
| ||||||
|
|
|
|
| 4 |
| 7 |
|
| |||
|
|
|
|
|
| 860 |
| 8 | " | |||
3 | / minimum |
|
| mm) | ||||||||
|
|
| ||||||||||
5 | " | (84 |
|
|
|
|
|
|
|
| ||
| 16 |
| mm) |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |||
5/8" - 2"
5 |
|
|
| 1 | 3 | " |
/ | " - |
|
| |||
8 | 2" |
| / | |||
| 50mm) |
| 16 |
| ||
bench |
|
|
|
| ||
|
|
| (15- |
|
|
|
|
| thickness | 1" |
|
| |
|
|
|
| Manifold |
|
|
|
|
|
| Center Line |
|
|
3/4" - 2"
3 |
|
|
|
|
|
|
|
/ | " | - | 2" |
|
|
|
|
4 | (19 |
|
|
| |||
bench | - 50 |
|
| ||||
|
| 1" | |||||
|
|
| thickness | mm) | |||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Manifold |
|
|
|
|
|
|
| Center Line |
3 "
/
4